Home › Guides › Formulas for the Technician exam
Formulas for the Technician exam
The Technician exam has only a handful of math questions, and they all use the same few formulas. Learn these and you pick up easy points.
Updated 2026-11-06
Ohm's law: E = I × R
- E is voltage in volts, I is current in amperes, R is resistance in ohms.
- Current: I = E / R. Example: 12 volts across 6 ohms gives 2 amperes.
- Resistance: R = E / I. Example: 90 volts and 3 amperes means 30 ohms.
- Voltage: E = I × R. Example: 2 amperes through 10 ohms gives 20 volts.
Power: P = E × I
- P is power in watts.
- Example: a 13.8-volt radio drawing 10 amperes uses 138 watts.
- Current from power: I = P / E. Example: 120 watts at 12 volts is 10 amperes.
Wavelength: meters = 300 / MHz
- Divide 300 by the frequency in megahertz to get the wavelength in meters.
- Example: 146 MHz gives about 2 meters, which is why that band is called 2 meters.
- Example: 28 MHz gives about 10.7 meters, the 10-meter band.
- Higher frequency means shorter wavelength.
- Try it: the frequency and wavelength calculator does the division for you and shows which band the frequency is in.
Antenna length: feet = 468 / MHz
- A half-wave dipole is about 468 divided by the frequency in MHz feet long, end to end. Each leg is half of that: 234 / MHz.
- A quarter-wave vertical uses the same 234 / MHz. Example: 234 / 146.52 = 1.60 feet, about 19 inches, the classic 2-meter whip (T9A08).
- These are starting lengths. Cut a little long and trim for the lowest SWR; shortening an antenna raises its resonant frequency (T9A05).
- Try it: the antenna length calculator gives feet, inches and meters.
Decibels: dB = 10 × log10(P2 / P1)
- 3 dB is double the power and -3 dB is half. 5 watts to 10 watts is 3 dB (T5B09); 12 watts to 3 watts is two halvings, -6 dB (T5B10).
- 10 dB is ten times the power. 20 watts to 200 watts is 10 dB (T5B11).
- Try it: the decibel calculator also converts watts to dBm and adds up feed line loss and antenna gain.
Unit prefixes
| Prefix | Means | Example |
|---|---|---|
| milli (m) | one thousandth | 1,500 milliamperes = 1.5 amperes |
| micro (µ) | one millionth | 1,000,000 microvolts = 1 volt |
| kilo (k) | thousand | 3,525 kHz = 3.525 MHz |
| mega (M) | million | 1 MHz = 1,000 kHz |
| giga (G) | billion | 2.425 GHz = 2,425 MHz |
| pico (p) | one trillionth | 500,000 pF = 0.5 µF |
Exam questions that use these formulas (T5C, T5D)
Practice these official pool questions. Each one links to a worked explanation.
All three calculators are collected on the ham radio calculators page.
- T5C01 What describes the ability to store energy in an electric field?
Capacitance - T5C02 What is the unit of capacitance?
Farad - T5C03 What describes the ability to store energy in a magnetic field?
Inductance - T5C04 What is the unit of inductance?
Henry - T5C05 What is the unit of impedance?
Ohm - T5C06 What is the abbreviation for kilohertz?
kHz - T5C07 What is the abbreviation for megahertz?
MHz - T5C08 What formula is used to calculate electrical power (P) in a DC circuit?
P = I x E - T5C09 How much power is delivered by a voltage of 13.8 volts DC and a current of 10 amperes?
138 watts - T5C10 How much power is delivered by a voltage of 12 volts DC and a current of 2.5 amperes?
30 watts - T5C11 How much current is required to deliver 120 watts at a voltage of 12 volts DC?
10 amperes - T5C12 What is impedance?
The opposition to AC current flow - T5D01 What formula is used to calculate current in a circuit?
I = E / R - T5D02 What formula is used to calculate voltage in a circuit?
E = I x R - T5D03 What formula is used to calculate resistance in a circuit?
R = E / I - T5D04 What is the resistance of a circuit in which a current of 3 amperes flows when connected to 90 volts?
30 ohms - T5D05 What is the resistance of a circuit for which the applied voltage is 12 volts and the current flow is 1.5 amperes?
8 ohms - T5D06 What is the resistance of a circuit that draws 4 amperes from a 12-volt source?
3 ohms - T5D07 What is the current in a circuit with an applied voltage of 120 volts and a resistance of 80 ohms?
1.5 amperes - T5D08 What is the current through a 100-ohm resistor connected across 200 volts?
2 amperes - T5D09 What is the current through a 24-ohm resistor connected across 240 volts?
10 amperes - T5D10 What is the voltage across a 2-ohm resistor if a current of 0.5 amperes flows through it?
1 volt - T5D11 What is the voltage across a 10-ohm resistor if a current of 1 ampere flows through it?
10 volts - T5D12 What is the voltage across a 10-ohm resistor if a current of 2 amperes flows through it?
20 volts - T5D13 In which type of circuit is the current always the same through all components?
Series - T5D14 In which type of circuit is the voltage always the same across all components?
Parallel
Questions people ask
Can I use a calculator on the ham radio exam?
Usually yes, if its memory is cleared. A phone calculator is not allowed. Check with your exam team.
How many math questions are on the Technician exam?
Only a few, mostly from the electrical principles topic (T5). The exact number changes with each exam.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- RF exposure safety, explained simply
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Electrical safety at your station
- Emergency communications for new hams
- Coax, connectors and SWR
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Ham radio Q codes and what they mean
- Fixing radio interference (RFI)
- How to sign up for the real exam
- Your first radio
- Ham radio calculators