Home › Guides › RF exposure safety, explained simply
RF exposure safety, explained simply
Radio transmitters put out energy that the body can absorb as heat. The FCC sets exposure limits, and every licensee must make sure their station stays within them. Question group T0C of the Technician pool covers it in 13 questions.
Updated 2026-10-23
Radio waves are non-ionizing
Radio signals are non-ionizing radiation (T0C01). Unlike X-rays or radioactivity, they do not carry enough energy to cause chemical changes in cells or damage DNA (T0C12). The concern is heating of body tissue, so the limits are about how much energy you absorb.
Why the limits depend on frequency
The body absorbs more RF energy at some frequencies than at others (T0C05). Among the Technician bands, 50 MHz (6 meters) has the lowest maximum permissible exposure (T0C02).
Duty cycle and averaging
Duty cycle is the percentage of time a transmitter is actually transmitting during the averaging time (T0C11). It matters because it changes your average exposure (T0C10). If the duty cycle drops from 100 percent to 50 percent, the allowable power density doubles (T0C03).
What affects exposure near your antenna
Power, frequency, distance from the antenna and the antenna's radiation pattern all count (T0C04). The simplest way to reduce exposure is to move the antenna farther from people (T0C08). Never touch an antenna while it is transmitting, because it can cause an RF burn (T0C07).
Who is responsible
The station licensee is responsible for keeping everyone below the FCC limits (T0C13). You can check compliance by calculation, by computer modeling or by measuring field strength (T0C06). Re-check whenever you change anything in the transmitter or antenna system (T0C09).
- T0C01 What type of radiation are radio signals?
Non-ionizing radiation - T0C02 Which of the following bands has the lowest maximum permissible exposure for RF safety?
50 MHz - T0C03 How does the allowable power density for RF safety change if duty cycle changes from 100 percent to 50 percent?
It increases by a factor of 2 - T0C04 What factors affect the RF exposure of people near an amateur station antenna?
All these choices are correct - T0C05 Why do exposure limits vary with frequency?
The human body absorbs more RF energy at some frequencies than at others - T0C06 Which of the following is an acceptable method to determine whether your station complies with FCC RF exposure regulations?
All these choices are correct - T0C07 What hazard is created by touching an antenna during a transmission?
RF burn to skin - T0C08 Which of the following actions can reduce exposure to RF radiation?
Relocate antennas - T0C09 How can you make sure your station stays in compliance with RF safety regulations?
By re-evaluating the station whenever an item in the transmitter or antenna system is changed - T0C10 Why is duty cycle one of the factors used to determine safe RF radiation exposure levels?
It affects the average exposure to radiation - T0C11 What is the definition of duty cycle during the averaging time for RF exposure?
The percentage of time that a transmitter is transmitting - T0C12 How does RF radiation differ from ionizing radiation (radioactivity)?
RF radiation does not have sufficient energy to cause chemical changes in cells and damage DNA - T0C13 Who is responsible for ensuring that no person is exposed to RF energy above the FCC exposure limits?
The station licensee
Questions people ask
Is RF from a ham radio dangerous?
Radio waves are non-ionizing. The risk is heating near the antenna at high power, which the FCC limits control.
What is duty cycle?
The percentage of time a transmitter is transmitting during the averaging time.
Who must make sure a station meets the exposure limits?
The station licensee.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- Formulas for the Technician exam
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Electrical safety at your station
- Emergency communications for new hams
- Coax, connectors and SWR
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Ham radio Q codes and what they mean
- Fixing radio interference (RFI)
- How to sign up for the real exam
- Your first radio
- Ham radio calculators