Home › Guides › Electrical safety at your station
Electrical safety at your station
Most ham stations run on 120 V AC power, 12 V batteries and power supplies. Each can hurt you or start a fire if it is wired wrong. Question group T0A covers the basics.
Updated 2026-10-24
Fuses and breakers
A fuse removes power when a circuit is overloaded (T0A04). Never replace a 5-ampere fuse with a 20-ampere one, because the extra current it allows could start a fire (T0A05). In a 120 V AC circuit, the fuse or breaker goes in series with the hot conductor only (T0A08). In U.S. wiring the black wire is the hot one (T0A03).
Lightning and grounding
Put the lightning arrester on a grounded panel near where the feed lines enter the building (T0A07). Bond all outside ground rods together with heavy wire or conductive strap (T0A09).
Batteries
Shorting the terminals of a 12-volt storage battery can cause burns, fire or an explosion (T0A01). Charging or discharging an unprotected battery too fast can make it overheat or give off gas (T0A10).
Power supplies and meters
A power supply can still hold a dangerous charge in its filter capacitors right after you turn it off (T0A11). When measuring high voltage, make sure the meter and its leads are rated for that voltage (T0A12).
Why current is dangerous
Current flowing through the body can cause heating, disrupt the electrical functions of cells and make muscles contract involuntarily (T0A02). See the RF safety guide for the separate rules on radio-frequency exposure.
Three-wire cords, a common safety ground for all AC equipment, and fully discharging high-voltage capacitors before working inside gear all guard against shock (T0A06).
- T0A01 Which of the following is a safety hazard of a 12-volt storage battery that lacks internal protection circuitry?
Shorting the terminals can cause burns, fire, or an explosion - T0A02 What health hazard is posed by electrical current flowing through the body?
All these choices are correct - T0A03 In the United States, what circuit does black wire insulation indicate in a three-wire 120 V AC cable?
Hot - T0A04 What is the purpose of a fuse in an electrical circuit?
To remove power in case of an overload - T0A05 Why should a 5-ampere fuse never be replaced with a 20-ampere fuse?
Excessive current could cause a fire - T0A06 What is a good way to guard against electrical shock at your station?
All these choices are correct - T0A07 Where should a lightning arrester be installed in a coaxial feed line?
On a grounded panel near where feed lines enter the building - T0A08 Where should a fuse or circuit breaker be installed in a 120V AC power circuit?
In series with the hot conductor only - T0A09 What should be done to all external ground rods or earth connections?
Bond them together with heavy wire or conductive strap - T0A10 What hazard exists when rapidly charging or discharging an unprotected battery?
Overheating or out-gassing - T0A11 What hazard exists in a power supply immediately after turning it off?
Charge stored in filter capacitors - T0A12 Which of the following precautions should be taken when measuring high voltages with a voltmeter?
Ensure that the voltmeter and its leads are rated for use at the voltages being measured
Questions people ask
Can I use a bigger fuse if mine keeps blowing?
No. A larger fuse lets excessive current flow and could cause a fire.
Where does a lightning arrester go?
On a grounded panel near where feed lines enter the building.
Is a power supply safe right after I switch it off?
Not always. Its filter capacitors can still hold a charge.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- Formulas for the Technician exam
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- RF exposure safety, explained simply
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Emergency communications for new hams
- Coax, connectors and SWR
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Ham radio Q codes and what they mean
- Fixing radio interference (RFI)
- How to sign up for the real exam
- Your first radio
- Ham radio calculators