Ham Tech Prep

Technician › T5

T5 Electrical Principles

50 questions in the pool. Your exam will include 4, one from each group below.

Practice T5 now

T5A

Current and voltage: terminology and units, conductors and insulators, alternating and direct current

T5A01

Electrical current is measured in which of the following units?

  1. A. Volts
  2. B. Watts
  3. C. Ohms
  4. D. Amperes
Show the answer and explanation

Answer: D. Amperes

Electrical current is measured in amperes (amps). Volts measure voltage, watts measure power, and ohms measure resistance.

Tip: Current = amps (I).

T5A02

Electrical power is measured in which of the following units?

  1. A. Volts
  2. B. Watts
  3. C. Watt-hours
  4. D. Amperes
Show the answer and explanation

Answer: B. Watts

Electrical power is measured in watts. Watt-hours measure energy used over time, not power itself.

Tip: Power = watts (P).

T5A03

What is the term for the flow of electrons in an electric circuit?

  1. A. Voltage
  2. B. Amperes per second
  3. C. Volts per second
  4. D. Current
Show the answer and explanation

Answer: D. Current

The flow of electrons in a circuit is called current. Voltage is the push that makes the electrons move, but the flow itself is current.

Tip: Current flows like water in a pipe.

T5A04

What term describes the number of times per second that an alternating current makes a complete cycle?

  1. A. Pulse rate
  2. B. Wave number
  3. C. Frequency
  4. D. Wavelength
Show the answer and explanation

Answer: C. Frequency

The number of complete cycles an alternating current makes each second is its frequency. Wavelength is the physical length of one wave, not a count per second.

Tip: Frequency = cycles per second (hertz).

T5A05

A difference in which of the following causes electron flow?

  1. A. Voltage
  2. B. Ampere-hours
  3. C. Capacitance
  4. D. Inductance
Show the answer and explanation

Answer: A. Voltage

Electrons flow when there is a difference in voltage between two points. Voltage is like pressure that pushes the electrons along. Capacitance and inductance store energy but do not themselves cause flow.

Tip: Voltage pushes, current flows.

T5A06

What is the unit of frequency?

  1. A. Hertz
  2. B. Henry
  3. C. Farad
  4. D. Epicycles per second
Show the answer and explanation

Answer: A. Hertz

The unit of frequency is the hertz, which means one cycle per second. The henry is the unit of inductance and the farad is the unit of capacitance.

Tip: Hertz = frequency; Henry = inductance; Farad = capacitance.

T5A07

Why are metals generally good conductors of electricity?

  1. A. They have relatively high density
  2. B. They have many free electrons
  3. C. They have many free protons
  4. D. They have relatively high Young's modulus values
Show the answer and explanation

Answer: B. They have many free electrons

Metals are good conductors because they have many free electrons. These loose electrons can move easily through the metal, carrying current. Protons stay in the atom's nucleus and do not move freely.

Tip: Free electrons make good conductors.

T5A08

Which of the following is a good electrical insulator?

  1. A. Sea water
  2. B. Glass
  3. C. Stainless steel
  4. D. Graphite
Show the answer and explanation

Answer: B. Glass

Glass is a good electrical insulator because it has very few free electrons to carry current. Sea water, stainless steel, and graphite all conduct electricity.

Tip: Glass, plastic, ceramic = insulators.

T5A09

Which of the following describes alternating current?

  1. A. Current that alternates between a positive direction and zero
  2. B. Current that alternates between a negative direction and zero
  3. C. Current that alternates between positive and negative directions
  4. D. All these answers are correct
Show the answer and explanation

Answer: C. Current that alternates between positive and negative directions

Alternating current is current that alternates between positive and negative directions. It flows one way, then reverses and flows the other way, over and over. Current that only goes between zero and one direction is not true AC.

Tip: AC goes back and forth; DC goes one way.

T5A10

Which term describes the rate at which electrical energy is used?

  1. A. Resistance
  2. B. Current
  3. C. Power
  4. D. Voltage
Show the answer and explanation

Answer: C. Power

Power is the rate at which electrical energy is used. One watt equals one joule of energy per second.

Tip: Power = how fast energy is used.

T5A11

What type of current flow is opposed by resistance?

  1. A. Direct current
  2. B. Alternating current
  3. C. RF current
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Resistance opposes any flow of current. That means direct current, alternating current, and RF current, so "All these choices are correct" is the answer.

Tip: Resistance resists every kind of current.

T5B

Math for electronics: conversion of electrical units, decibels

T5B01

How many milliamperes is 1.5 amperes?

  1. A. 0.0000015 milliamperes
  2. B. 0.0015 milliamperes
  3. C. 1500 milliamperes
  4. D. 1,500,000 milliamperes
Show the answer and explanation

Answer: C. 1500 milliamperes

"Milli" means one-thousandth, so there are 1000 milliamperes in 1 ampere. Step: 1.5 A x 1000 = 1500 milliamperes.

Tip: Amps to milliamps: multiply by 1000.

T5B02

Which is equal to 1,500,000 hertz?

  1. A. 1500 kHz
  2. B. 1500 MHz
  3. C. 15 GHz
  4. D. 150 kHz
Show the answer and explanation

Answer: A. 1500 kHz

"Kilo" means 1000, so 1 kHz = 1000 Hz. Step: 1,500,000 Hz / 1000 = 1500 kHz. That is also 1.5 MHz, but 1500 MHz would be a thousand times too big.

Tip: Hz to kHz: divide by 1000.

T5B03

Which is equal to one kilovolt?

  1. A. One one-thousandth of a volt
  2. B. One hundred volts
  3. C. One thousand volts
  4. D. One million volts
Show the answer and explanation

Answer: C. One thousand volts

"Kilo" means one thousand, so one kilovolt is one thousand volts. One one-thousandth of a volt would be a millivolt.

Tip: kilo = 1000.

T5B04

Which is equal to one microvolt?

  1. A. One one-millionth of a volt
  2. B. One million volts
  3. C. One thousand kilovolts
  4. D. One one-thousandth of a volt
Show the answer and explanation

Answer: A. One one-millionth of a volt

"Micro" means one-millionth, so one microvolt is one one-millionth of a volt (0.000001 V). One one-thousandth of a volt is a millivolt, which is much larger.

Tip: micro = 1/1,000,000; milli = 1/1000.

T5B05

Which is equal to 500 milliwatts?

  1. A. 5 watts
  2. B. 0.5 watts
  3. C. 500,000 watts
  4. D. 500,000,000 watts
Show the answer and explanation

Answer: B. 0.5 watts

There are 1000 milliwatts in 1 watt. Step: 500 mW / 1000 = 0.5 watts.

Tip: mW to W: divide by 1000.

T5B06

Which is equal to 3000 milliamperes?

  1. A. 0.003 amperes
  2. B. 0.3 amperes
  3. C. 3,000,000 amperes
  4. D. 3 amperes
Show the answer and explanation

Answer: D. 3 amperes

There are 1000 milliamperes in 1 ampere. Step: 3000 mA / 1000 = 3 amperes.

Tip: mA to A: divide by 1000.

T5B07

Which is equal to 3.525 MHz?

  1. A. 0.003525 kHz
  2. B. 35.25 kHz
  3. C. 3525 kHz
  4. D. 3,525,000 kHz
Show the answer and explanation

Answer: C. 3525 kHz

1 MHz = 1000 kHz. Step: 3.525 MHz x 1000 = 3525 kHz. Going to a smaller unit makes the number bigger.

Tip: MHz to kHz: multiply by 1000.

T5B08

Which is equal to 1,000,000 picofarads?

  1. A. 0.001 microfarads
  2. B. 1 microfarad
  3. C. 1000 microfarads
  4. D. 1,000,000,000 microfarads
Show the answer and explanation

Answer: B. 1 microfarad

A picofarad is one-millionth of a microfarad, so 1,000,000 pF = 1 microfarad. Step: 1,000,000 pF / 1,000,000 = 1 uF.

Tip: 1 uF = 1,000,000 pF.

T5B09

Which decibel value most closely represents a power increase from 5 watts to 10 watts?

  1. A. 2 dB
  2. B. 3 dB
  3. C. 5 dB
  4. D. 10 dB
Show the answer and explanation

Answer: B. 3 dB

Decibels for power use dB = 10 x log(P2 / P1). Step: 10 W / 5 W = 2, and 10 x log(2) = 10 x 0.301 = about 3 dB. So doubling the power is a 3 dB increase.

Tip: Double the power = +3 dB.

T5B10

Which decibel value most closely represents a power decrease from 12 watts to 3 watts?

  1. A. -1 dB
  2. B. -3 dB
  3. C. -6 dB
  4. D. -9 dB
Show the answer and explanation

Answer: C. -6 dB

dB = 10 x log(P2 / P1). Step: 3 W / 12 W = 0.25, and 10 x log(0.25) = about -6.02, so about -6 dB. Another way: 12 to 6 W is half (-3 dB), and 6 to 3 W is half again (-3 dB), for a total of -6 dB.

Tip: Each halving of power = -3 dB.

T5B11

Which decibel value represents a power increase from 20 watts to 200 watts?

  1. A. 10 dB
  2. B. 12 dB
  3. C. 18 dB
  4. D. 28 dB
Show the answer and explanation

Answer: A. 10 dB

dB = 10 x log(P2 / P1). Step: 200 W / 20 W = 10, and 10 x log(10) = 10 x 1 = 10 dB. Ten times the power is a 10 dB increase.

Tip: 10 times the power = +10 dB.

T5B12

Which is equal to 28400 kHz?

  1. A. 28.400 kHz
  2. B. 2.800 MHz
  3. C. 284.00 MHz
  4. D. 28.400 MHz
Show the answer and explanation

Answer: D. 28.400 MHz

1 MHz = 1000 kHz. Step: 28400 kHz / 1000 = 28.400 MHz. Going to a bigger unit makes the number smaller.

Tip: kHz to MHz: divide by 1000.

T5B13

Which is equal to 2425 MHz?

  1. A. 0.002425 GHz
  2. B. 24.25 GHz
  3. C. 2.425 GHz
  4. D. 242.5 GHz
Show the answer and explanation

Answer: C. 2.425 GHz

1 GHz = 1000 MHz. Step: 2425 MHz / 1000 = 2.425 GHz.

Tip: MHz to GHz: divide by 1000.

T5C

Capacitance and inductance terminology and units; Radio frequency definition and units; Impedance definition and units; Calculating power

T5C01

What describes the ability to store energy in an electric field?

  1. A. Inductance
  2. B. Resistance
  3. C. Frequency
  4. D. Capacitance
Show the answer and explanation

Answer: D. Capacitance

Capacitance is the ability to store energy in an electric field. A capacitor stores this energy between its plates. Inductance stores energy in a magnetic field instead.

Tip: Capacitor = electric field; inductor = magnetic field.

T5C02

What is the unit of capacitance?

  1. A. Farad
  2. B. Ohm
  3. C. Volt
  4. D. Henry
Show the answer and explanation

Answer: A. Farad

The unit of capacitance is the farad, named after Michael Faraday. The henry is for inductance and the ohm is for resistance.

Tip: Capacitance in farads.

T5C03

What describes the ability to store energy in a magnetic field?

  1. A. Admittance
  2. B. Capacitance
  3. C. Resistance
  4. D. Inductance
Show the answer and explanation

Answer: D. Inductance

Inductance is the ability to store energy in a magnetic field. An inductor, usually a coil of wire, builds a magnetic field when current flows through it.

Tip: Coil + current = magnetic field = inductance.

T5C04

What is the unit of inductance?

  1. A. Coulomb
  2. B. Farad
  3. C. Henry
  4. D. Ohm
Show the answer and explanation

Answer: C. Henry

The unit of inductance is the henry. The farad is for capacitance and the ohm is for resistance and impedance.

Tip: Inductance in henrys.

T5C05

What is the unit of impedance?

  1. A. Volt
  2. B. Ampere
  3. C. Coulomb
  4. D. Ohm
Show the answer and explanation

Answer: D. Ohm

Impedance is the total opposition to AC current, and like resistance it is measured in ohms.

Tip: Resistance, reactance, impedance: all in ohms.

T5C06

What is the abbreviation for kilohertz?

  1. A. kHz
  2. B. khz
  3. C. KHz
  4. D. KHZ
Show the answer and explanation

Answer: A. kHz

The correct abbreviation for kilohertz is kHz. The "k" for kilo is lowercase and "Hz" for hertz has a capital H and a lowercase z.

Tip: Lowercase k, capital H, lowercase z: kHz.

T5C07

What is the abbreviation for megahertz?

  1. A. mHz
  2. B. mHZ
  3. C. Mhz
  4. D. MHz
Show the answer and explanation

Answer: D. MHz

The correct abbreviation for megahertz is MHz. A capital M means mega (million), while a lowercase m means milli (one-thousandth), so case matters.

Tip: Capital M = mega; small m = milli.

T5C08

What formula is used to calculate electrical power (P) in a DC circuit?

  1. A. P = I x E
  2. B. P = E / I
  3. C. P = I2 x E
  4. D. P = I / E
Show the answer and explanation

Answer: A. P = I x E

Power equals current times voltage, written P = I x E. Here I is current in amps and E is voltage in volts, giving P in watts.

Tip: PIE: P = I x E.

T5C09

How much power is delivered by a voltage of 13.8 volts DC and a current of 10 amperes?

  1. A. 138 watts
  2. B. 0.7 watts
  3. C. 23.8 watts
  4. D. 3.8 watts
Show the answer and explanation

Answer: A. 138 watts

Use P = I x E. Step: P = 10 A x 13.8 V = 138 watts.

Tip: P = I x E.

T5C10

How much power is delivered by a voltage of 12 volts DC and a current of 2.5 amperes?

  1. A. 4.8 watts
  2. B. 30 watts
  3. C. 14.5 watts
  4. D. 0.208 watts
Show the answer and explanation

Answer: B. 30 watts

Use P = I x E. Step: P = 2.5 A x 12 V = 30 watts.

Tip: P = I x E.

T5C11

How much current is required to deliver 120 watts at a voltage of 12 volts DC?

  1. A. 0.1 amperes
  2. B. 10 amperes
  3. C. 12 amperes
  4. D. 132 amperes
Show the answer and explanation

Answer: B. 10 amperes

Rearrange P = I x E to get I = P / E. Step: I = 120 W / 12 V = 10 amperes.

Tip: I = P / E.

T5C12

What is impedance?

  1. A. The opposition to AC current flow
  2. B. The inverse of resistance
  3. C. The inverse of reactance
  4. D. The power handling capability of a component
Show the answer and explanation

Answer: A. The opposition to AC current flow

Impedance is the opposition to AC current flow. It combines resistance and reactance and is measured in ohms. It is not the inverse of resistance; that would be conductance.

Tip: Impedance = AC's version of resistance.

T5D

Ohm's Law; Series and parallel circuits

T5D01

What formula is used to calculate current in a circuit?

  1. A. I = E x R
  2. B. I = E / R
  3. C. I = E2 x R
  4. D. I = E2 / R
Show the answer and explanation

Answer: B. I = E / R

Ohm's law says E = I x R. Solving for current gives I = E / R: current equals voltage divided by resistance.

Tip: Ohm's law triangle: E on top, I and R on bottom.

T5D02

What formula is used to calculate voltage in a circuit?

  1. A. E = I x R
  2. B. E = I / R
  3. C. E = I2 x R
  4. D. E = I2 / R
Show the answer and explanation

Answer: A. E = I x R

Ohm's law: voltage equals current times resistance, E = I x R.

Tip: E = I x R.

T5D03

What formula is used to calculate resistance in a circuit?

  1. A. R = E x I
  2. B. R = E / I
  3. C. R = E + I
  4. D. R = E - I
Show the answer and explanation

Answer: B. R = E / I

Ohm's law: E = I x R. Solving for resistance gives R = E / I: resistance equals voltage divided by current.

Tip: R = E / I.

T5D04

What is the resistance of a circuit in which a current of 3 amperes flows when connected to 90 volts?

  1. A. 3 ohms
  2. B. 30 ohms
  3. C. 1/30 ohm
  4. D. 270 ohms
Show the answer and explanation

Answer: B. 30 ohms

Use R = E / I. Step: R = 90 V / 3 A = 30 ohms. Multiplying (270) is a common mistake.

Tip: R = E / I.

T5D05

What is the resistance of a circuit for which the applied voltage is 12 volts and the current flow is 1.5 amperes?

  1. A. 18 ohms
  2. B. 0.125 ohms
  3. C. 8 ohms
  4. D. 13.5 ohms
Show the answer and explanation

Answer: C. 8 ohms

Use R = E / I. Step: R = 12 V / 1.5 A = 8 ohms.

Tip: R = E / I.

T5D06

What is the resistance of a circuit that draws 4 amperes from a 12-volt source?

  1. A. 3 ohms
  2. B. 16 ohms
  3. C. 48 ohms
  4. D. 8 ohms
Show the answer and explanation

Answer: A. 3 ohms

Use R = E / I. Step: R = 12 V / 4 A = 3 ohms.

Tip: R = E / I.

T5D07

What is the current in a circuit with an applied voltage of 120 volts and a resistance of 80 ohms?

  1. A. 9600 amperes
  2. B. 200 amperes
  3. C. 0.667 amperes
  4. D. 1.5 amperes
Show the answer and explanation

Answer: D. 1.5 amperes

Use I = E / R. Step: I = 120 V / 80 ohms = 1.5 amperes. Dividing the other way (80 / 120) gives the wrong answer 0.667.

Tip: I = E / R.

T5D08

What is the current through a 100-ohm resistor connected across 200 volts?

  1. A. 20,000 amperes
  2. B. 0.5 amperes
  3. C. 2 amperes
  4. D. 100 amperes
Show the answer and explanation

Answer: C. 2 amperes

Use I = E / R. Step: I = 200 V / 100 ohms = 2 amperes.

Tip: I = E / R.

T5D09

What is the current through a 24-ohm resistor connected across 240 volts?

  1. A. 2400 amperes
  2. B. 0.1 amperes
  3. C. 10 amperes
  4. D. 5760 amperes
Show the answer and explanation

Answer: C. 10 amperes

Use I = E / R. Step: I = 240 V / 24 ohms = 10 amperes.

Tip: I = E / R.

T5D10

What is the voltage across a 2-ohm resistor if a current of 0.5 amperes flows through it?

  1. A. 1 volt
  2. B. 0.25 volts
  3. C. 2.5 volts
  4. D. 1.5 volts
Show the answer and explanation

Answer: A. 1 volt

Use E = I x R. Step: E = 0.5 A x 2 ohms = 1 volt.

Tip: E = I x R.

T5D11

What is the voltage across a 10-ohm resistor if a current of 1 ampere flows through it?

  1. A. 1 volt
  2. B. 10 volts
  3. C. 11 volts
  4. D. 9 volts
Show the answer and explanation

Answer: B. 10 volts

Use E = I x R. Step: E = 1 A x 10 ohms = 10 volts.

Tip: E = I x R.

T5D12

What is the voltage across a 10-ohm resistor if a current of 2 amperes flows through it?

  1. A. 8 volts
  2. B. 0.2 volts
  3. C. 12 volts
  4. D. 20 volts
Show the answer and explanation

Answer: D. 20 volts

Use E = I x R. Step: E = 2 A x 10 ohms = 20 volts.

Tip: E = I x R.

T5D13

In which type of circuit is the current always the same through all components?

  1. A. Series
  2. B. Parallel
  3. C. Resonant
  4. D. Branch
Show the answer and explanation

Answer: A. Series

In a series circuit, there is only one path for current, so the current is always the same through all components. In a parallel circuit, current splits among the branches.

Tip: Series: same current. Parallel: same voltage.

T5D14

In which type of circuit is the voltage always the same across all components?

  1. A. Series
  2. B. Parallel
  3. C. Resonant
  4. D. Branch
Show the answer and explanation

Answer: B. Parallel

In a parallel circuit, every component is connected across the same two points, so the voltage is always the same across all of them. In a series circuit, the voltage is divided among the parts.

Tip: Parallel: same voltage. Series: same current.

Practice T5 with scoring Take a 35-question practice exam