Home › Guides › Ham radio Q codes and what they mean
Ham radio Q codes and what they mean
Q signals are three-letter codes that start with Q. They were made for Morse code, where short codes save time, but hams also say them on voice. The Technician exam asks about two of them.
Updated 2026-11-19
The Q signals you will hear most
Every Q signal has two forms. Sent alone it is a statement; followed by a question mark it is a question. "QTH?" means "Where are you?", and "QTH Denver" is the answer.
| Code | Meaning | As a question (with ?) |
|---|---|---|
| QRM | Interference from other stations | Is my signal getting interference? |
| QRN | Natural noise, such as static from storms | Are you troubled by static? |
| QSB | Your signal is fading | Is my signal fading? |
| QSY | Change to another frequency | Shall I change frequency? |
| QSL | I confirm I received it | Can you confirm receipt? |
| QTH | My location is ... | What is your location? |
| QRZ | You are being called by ... | Who is calling me? |
| QRL | This frequency is busy | Is this frequency in use? |
| QRP | Reduce power (low power) | Shall I reduce power? |
| QRO | Increase power (high power) | Shall I increase power? |
| QRT | Stop sending | Shall I stop sending? |
| QRX | Wait | When will you call me again? |
| QRS / QRQ | Send more slowly / faster | Shall I send slower / faster? |
Q codes on the Technician exam
- T2B10: the Q signal for interference from other stations is QRM. Do not mix it up with QRN, which is natural noise.
- T2B11: the Q signal for changing frequency is QSY.
- T2C03: to make sure unusual words are received correctly on voice, spell them with the phonetic alphabet. The answer is not a Q code.
- T2B01 What is the purpose of the reverse function on a VHF/UHF transceiver?
To listen on a repeater's input frequency - T2B02 What term describes the use of a sub-audible tone transmitted along with normal voice audio to open the squelch of a receiver?
CTCSS - T2B03 Which of the following describes a linked repeater network?
A network of repeaters in which signals received by one repeater are transmitted by all the repeaters in the network - T2B04 Which of the following could be the reason you are unable to access a repeater whose output you can hear?
All these choices are correct - T2B05 Which of the following would cause your FM transmission audio to drop out on voice peaks?
You are talking too loudly - T2B06 What type of signaling to a repeater uses two simultaneous audio tones?
DTMF - T2B07 How can you join a digital repeater's “talkgroup”?
Program your radio with the group's ID or code - T2B08 Which of the following applies when two stations transmitting on the same frequency interfere with each other?
The stations should negotiate continued use of the frequency - T2B09 Why are simplex channels designated in the VHF/UHF band plans?
So stations within range of each other can communicate without tying up a repeater - T2B10 Which Q signal indicates that you are receiving interference from other stations?
QRM - T2B11 Which Q signal indicates that you are changing frequency?
QSY - T2B12 What is the digital color code used on DMR repeater systems?
An access code which must be programmed into a DMR transmitter to access a specific repeater - T2B13 What is the purpose of a squelch function?
Mute the receiver audio when a signal is not present - T2B14 Which of the following is a “talkgroup”?
An identifier used by DMR to organize radio traffic so that those who want to hear the group aren't bothered by other radio traffic
Ham words that grew out of Q codes
- QSO means a two-way contact. "Thanks for the QSO" means thanks for the chat.
- QSL card is the postcard (or online record) two stations exchange to confirm a contact. The name comes from QSL, "I confirm receipt".
- QRP is also the name for low-power operating, a popular hobby within the hobby.
- QTH is often used for your home station: "my QTH" means where I operate from.
Should you use Q codes on voice?
On CW they are normal. On voice, plain speech is clearer, especially on local repeaters, and many operators prefer "changing frequency" to "QSY". A few, such as QTH, QSL and QRM, are used on voice so often that you will hear them on almost every band. When in doubt, say it in plain English.
Questions people ask
What is the difference between QRM and QRN?
QRM is interference from other stations (man-made). QRN is natural noise such as static from lightning.
Do I need to memorize all Q codes for the Technician exam?
No. The Technician pool asks about QRM (T2B10) and QSY (T2B11). Knowing a few others helps you understand what you hear on the air.
What does 73 mean?
73 is not a Q code. It is an old telegraph number code that means "best regards" and is used to end a contact.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- Formulas for the Technician exam
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- RF exposure safety, explained simply
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Electrical safety at your station
- Emergency communications for new hams
- Coax, connectors and SWR
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Fixing radio interference (RFI)
- How to sign up for the real exam
- Your first radio
- Ham radio calculators