Home › Guides › Fixing radio interference (RFI)
Fixing radio interference (RFI)
Sooner or later a neighbor may say your radio is coming through their TV, or your own receiver fills with noise from something next door. The Technician exam covers the polite, step-by-step way to deal with both in question group T7B.
Updated 2026-11-22 · Source: Technician question pool, group T7B
If a neighbor says you interfere with them
- Check your own station first. Make sure it works properly and does not interfere with your own radio or TV tuned to the same channel (T7B06).
- Look at the cable TV connections. For non-fiber cable TV, the first step is making sure all the TV feed line coaxial connectors are installed properly (T7B09).
- Add a filter at their receiver. A filter at the antenna input of the affected receiver can block your signal (T7B05).
- Know why it happens. A broadcast AM or FM radio picks you up when it cannot reject strong signals outside its band (T7B02). That is a receiver weakness, but working with your neighbor still matters.
- Know the technical causes. Fundamental overload, harmonics and spurious emissions can all cause radio frequency interference (T7B03).
If something in their home interferes with you
Work with your neighbor to find the device causing it, politely let them know the FCC rules prohibit devices that cause harmful interference, and make sure your own station meets the standards of good amateur practice. The exam answer is "All these choices are correct" (T7B08).
Problems with your own signal
| Symptom | Likely cause or fix | Question |
|---|---|---|
| Told you are over-deviating on FM | Talk farther from the microphone | T7B01 |
| Distorted or unintelligible audio through a repeater | Slightly off frequency, speaking too loudly or too close to the mic, or a bad location; all are possible | T7B10 |
| Distorted voice caused by RF feedback | Clip-on ferrite choke on the microphone cable | T7B11 |
| Low RF power from a solid-state radio | High SWR | T7B04 |
| 2-meter radio overloaded by a nearby FM broadcast station | Band-reject filter | T7B07 |
Exam questions on this topic (T7B)
- T7B01 What can you do if you are told your FM handheld or mobile transceiver is over-deviating?
Talk farther away from the microphone - T7B02 What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally?
The receiver is unable to reject strong signals outside the AM or FM band - T7B03 Which of the following can cause radio frequency interference?
All these choices are correct - T7B04 Which of the following might be the cause of low RF power output from a solid-state transceiver?
High SWR - T7B05 Which of the following might reduce interference by an amateur station to a non-amateur over-the-air radio receiver?
Block the amateur signal with a filter at the antenna input of the affected receiver - T7B06 Which of the following actions should you take if a neighbor tells you that your station's transmissions are interfering with their radio or TV reception?
Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel - T7B07 Which of the following can reduce interference to a 2-meter band transceiver from a nearby commercial FM station?
Installing a band-reject filter - T7B08 What should you do if something in a neighbor's home is causing harmful interference to your amateur station?
All these choices are correct - T7B09 What should be the first step to resolve non-fiber optic cable TV interference caused by your amateur radio transmission?
Be sure all TV feed line coaxial connectors are installed properly - T7B10 What might be a problem if you receive a report that your audio signal through an FM repeater is distorted or unintelligible?
All these choices are correct - T7B11 Which of the following can eliminate distorted voice transmissions?
Adding a clip-on ferrite “choke” to the microphone cable to prevent the transmitted signal from feeding back into the transmitter
Questions people ask
Is it my fault if my signal shows up on a neighbor's TV?
Not always. Many consumer devices cannot reject strong nearby signals. Still, start by confirming your own station is clean, then help with filters and connectors.
What is a ferrite choke?
A clip-on ferrite core on a cable that blocks RF from traveling along it. On a microphone cable it can stop RF feedback that distorts your voice (T7B11).
Why does high SWR lower my power?
Solid-state transmitters protect themselves by reducing output when SWR is high. See coax and SWR.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- Formulas for the Technician exam
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- RF exposure safety, explained simply
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Electrical safety at your station
- Emergency communications for new hams
- Coax, connectors and SWR
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Ham radio Q codes and what they mean
- How to sign up for the real exam
- Your first radio
- Ham radio calculators