Home › Guides › Coax, connectors and SWR
Coax, connectors and SWR
The feed line carries your signal from the radio to the antenna, and a poor one can waste much of your power. Question group T9B covers the basics every new ham should know before buying cable.
Updated 2026-11-06
Coaxial cable
Coax is the most common feed line because it is easy to use and needs few special installation steps (T9B03). Most amateur coax has an impedance of 50 ohms (T9B02). The higher the frequency, the more signal the cable loses (T9B05).
| Cable | Note | Question |
|---|---|---|
| RG-58 | More loss than RG-213 at the same frequency | T9B10 |
| RG-213 | Thicker, less loss at the same frequency | T9B10 |
| Air-insulated hardline | Lowest loss of the common types | T9B11 |
Connectors
PL-259 connectors are common at HF and VHF (T9B07). Above 400 MHz, a Type N connector is the better choice (T9B06). Any connector used outdoors, whether PL-259, BNC or Type N, should be carefully taped against the weather (T9B01).
Where signal gets lost
Water getting into connectors, high SWR and too many connectors in the line all add loss (T9B08). Use one good run of cable where you can.
To see what a few dB of cable loss costs in watts, try the gain and loss chain in the decibel calculator.
SWR and antenna tuners
SWR (standing wave ratio) measures how well the load, usually your antenna, is matched to the feed line (T9B12). If SWR jumps around, look for a loose connection at the antenna or in the feed line (T9B09). An antenna tuner matches the antenna system's impedance to the radio's output impedance (T9B04). See antenna basics for how antenna length sets the frequency.
- T9B01 Which of the following connectors should be carefully taped for weather protection when used outdoors?
All these choices are correct - T9B02 What is the most common impedance of coaxial cables used in amateur radio?
50 ohms - T9B03 Why is coaxial cable the most common feed line for amateur radio antenna systems?
It is easy to use and requires few special installation considerations - T9B04 What is the major function of an antenna tuner (antenna coupler)?
It matches the antenna system impedance to the transceiver's output impedance - T9B05 What happens as the frequency of a signal in coaxial cable is increased?
The loss increases - T9B06 Which of the following connector types is most suitable as an RF connector for frequencies above 400 MHz?
Type N - T9B07 Which of the following is true of PL-259 type coax connectors?
They are commonly used at HF and VHF frequencies - T9B08 Which of the following is a source of loss in coaxial feed line?
All these choices are correct - T9B09 What can cause erratic changes in SWR?
Loose connection in the antenna or feed line - T9B10 What is the electrical difference between RG-58 and RG-213 coaxial cable?
RG-213 cable has less loss at a given frequency - T9B11 Which of the following types of feed line has the lowest loss?
Air-insulated hardline - T9B12 What is standing wave ratio (SWR)?
A measure of how well a load is matched to a transmission line
Questions people ask
What impedance is ham radio coax?
Most commonly 50 ohms.
Which has less loss, RG-58 or RG-213?
RG-213 has less loss at a given frequency.
What does SWR measure?
How well a load is matched to a transmission line.
Take a practice examPractice by topic
More guides
- Technician frequencies and privileges
- Technician vs General license
- How the Technician exam works
- Formulas for the Technician exam
- How to renew a ham radio license
- How to get a vanity call sign
- The phonetic alphabet for ham radio
- Repeater basics for new Technicians
- RF exposure safety, explained simply
- How to make your first contact
- Antenna basics for new hams
- How radio signals travel
- Electrical safety at your station
- Emergency communications for new hams
- Amateur satellites and the ISS
- Digital modes and internet linking
- Technician study plan
- ARRL Field Day: a first-timer's guide
- Electronic components on the Technician exam
- Do you need Morse code for a ham license?
- What you can't transmit on ham radio
- Ham radio Q codes and what they mean
- Fixing radio interference (RFI)
- How to sign up for the real exam
- Your first radio
- Ham radio calculators