Technician › T7
T7 Practical Circuits
44 questions in the pool. Your exam will include 4, one from each group below.
T7A
Station equipment: receivers, transceivers, transmitter amplifiers, RF preamplifiers, transverters; Basic radio circuit concepts and terminology: sensitivity, selectivity, mixers, oscillators, Push-To-Talk (PTT), VFO, modulation
T7A01
Which term describes the ability of a receiver to detect the presence of a signal?
- A. RF gain
- B. Sensitivity
- C. Selectivity
- D. Total Harmonic Distortion
Show the answer and explanation
Answer: B. Sensitivity
Sensitivity is how well a receiver can pick up, or detect, weak signals. A more sensitive receiver can hear fainter stations. Selectivity is a different idea: separating signals that are close together.
Tip: Sensitivity senses weak signals.
T7A02
What is a transceiver?
- A. A device that combines a receiver and transmitter
- B. A device for matching feed line impedance to 50 ohms
- C. A device for automatically sending and decoding Morse code
- D. A device for converting receiver and transmitter frequencies to another band
Show the answer and explanation
Answer: A. A device that combines a receiver and transmitter
A transceiver is a single radio that combines a transmitter and a receiver. Most amateur radios, from handhelds to base stations, are transceivers.
Tip: TRANSmitter + reCEIVER = transceiver.
T7A03
Which of the following is used to convert a signal from one frequency to another?
- A. Phase splitter
- B. Mixer
- C. Inverter
- D. Amplifier
Show the answer and explanation
Answer: B. Mixer
A mixer combines two signals to produce new frequencies, such as their sum and difference. Radios use mixers to convert a signal from one frequency to another. An amplifier makes a signal stronger but keeps the same frequency.
Tip: Mixer mixes signals to move frequency.
T7A04
Which term describes the ability of a receiver to discriminate between multiple signals?
- A. Discrimination ratio
- B. Sensitivity
- C. Selectivity
- D. Harmonic distortion
Show the answer and explanation
Answer: C. Selectivity
Selectivity is a receiver's ability to separate the signal you want from others on nearby frequencies. Good selectivity keeps a nearby strong station from drowning out the one you are listening to. Sensitivity is about hearing weak signals, not separating them.
Tip: Selectivity selects one signal from many.
T7A05
What is the name of a circuit that generates a signal at a specific frequency?
- A. Reactance modulator
- B. Phase modulator
- C. Low-pass filter
- D. Oscillator
Show the answer and explanation
Answer: D. Oscillator
An oscillator is a circuit that generates a signal at a specific frequency. Every transmitter and most receivers use oscillators. A low-pass filter blocks frequencies; it does not create them.
Tip: Oscillators oscillate: they make the signal.
T7A06
What device converts the RF input and output of a transceiver to another band?
- A. High-pass filter
- B. Low-pass filter
- C. Transverter
- D. Phase converter
Show the answer and explanation
Answer: C. Transverter
A transverter converts a transceiver's RF input and output to a different band. For example, it can let an HF radio work on a VHF or microwave band. Its name combines 'transmit' and 'converter.'
Tip: TRANSmit + conVERTER = transverter, for a new band.
T7A07
What is the function of a transceiver's PTT input?
- A. Input for a key used to send CW
- B. Switches transceiver from receive to transmit when grounded
- C. Provides a transmit tuning tone when grounded
- D. Input for a preamplifier tuning tone
Show the answer and explanation
Answer: B. Switches transceiver from receive to transmit when grounded
PTT means push-to-talk. When the PTT input is grounded, such as by pressing the microphone button, the transceiver switches from receive to transmit. A CW key usually plugs into a separate key jack.
Tip: Push to talk: ground the PTT line to transmit.
T7A08
Which of the following describes combining speech with an RF carrier signal?
- A. Impedance matching
- B. Oscillation
- C. Modulation
- D. Low-pass filtering
Show the answer and explanation
Answer: C. Modulation
Modulation is the process of combining information, like your voice, with an RF carrier signal so it can be sent over the air. AM, FM, and SSB are all types of modulation.
Tip: Modulation puts your voice on the carrier.
T7A09
What is the function of the switch which selects either SSB or CW-FM on some VHF power amplifiers?
- A. Change the mode of the transmitted signal
- B. Set the amplifier for proper operation in the selected mode
- C. Change the frequency range of the amplifier to operate in the proper segment of the band
- D. Reduce the received signal noise
Show the answer and explanation
Answer: B. Set the amplifier for proper operation in the selected mode
Some VHF amplifiers have a switch for SSB or CW-FM so the amplifier is set up to work properly in that mode. SSB needs a linear amplifier, while CW and FM can use a more efficient, non-linear setting. The switch does not change the mode the radio transmits.
Tip: The switch sets up the amp, not the radio's mode.
T7A10
What can be added to the output of a transceiver to increase the transmitted output power?
- A. A potentiometer
- B. An RF power amplifier
- C. An impedance multiplier
- D. All these choices are correct
Show the answer and explanation
Answer: B. An RF power amplifier
An RF power amplifier added to the transceiver's output boosts the transmitted power. A potentiometer cannot add power, and 'impedance multiplier' is not a device for this job.
Tip: Need more watts? Add an RF power amplifier.
T7A11
What is the function of the Variable Frequency Oscillator (VFO) circuit in a transceiver?
- A. Set the receive and transmit frequency
- B. Provide automatic frequency control
- C. Inject a variable frequency to allow CW reception
- D. Generate and demodulate single sideband signals
Show the answer and explanation
Answer: A. Set the receive and transmit frequency
The VFO, or variable frequency oscillator, is the circuit that sets the frequency the transceiver receives and transmits on. Turning the main tuning knob changes the VFO.
Tip: VFO = the tuning dial's frequency.
T7B
Symptoms, causes, and cures of common transmitter and receiver problems: overload and overdrive, distortion, interference and consumer electronics, RF feedback
T7B01
What can you do if you are told your FM handheld or mobile transceiver is over-deviating?
- A. Talk louder into the microphone
- B. Let the transceiver cool off
- C. Change to a higher power level
- D. Talk farther away from the microphone
Show the answer and explanation
Answer: D. Talk farther away from the microphone
Over-deviation means your FM signal swings too wide, usually because your voice is too loud at the microphone. Moving the microphone farther away lowers the audio level and reduces deviation. Talking louder would make it worse.
Tip: Over-deviating? Back away from the mic.
T7B02
What would cause a broadcast AM or FM radio to receive an amateur radio transmission unintentionally?
- A. The receiver is unable to reject strong signals outside the AM or FM band
- B. The microphone gain of the transmitter is turned up too high
- C. The audio amplifier of the transmitter is overloaded
- D. The deviation of an FM transmitter is set too low
Show the answer and explanation
Answer: A. The receiver is unable to reject strong signals outside the AM or FM band
Broadcast AM and FM radios often cannot reject strong signals that are outside their own band. A nearby amateur transmitter can overload the receiver and be heard even though it is on a different frequency. This is a weakness of the receiver, not a fault in the amateur's audio settings.
Tip: Strong nearby signals can overwhelm a cheap receiver.
T7B03
Which of the following can cause radio frequency interference?
- A. Fundamental overload
- B. Harmonics
- C. Spurious emissions
- D. All these choices are correct
Show the answer and explanation
Answer: D. All these choices are correct
Fundamental overload, harmonics, and spurious emissions can all cause radio frequency interference. Overload happens when a strong signal swamps a receiver; harmonics and spurious emissions are unwanted signals on other frequencies. So all these choices are correct.
Tip: Overload, harmonics, spurs: all can cause RFI.
T7B04
Which of the following might be the cause of low RF power output from a solid-state transceiver?
- A. Poor amplifier noise figure
- B. Poor amplifier linearity
- C. Low SWR
- D. High SWR
Show the answer and explanation
Answer: D. High SWR
High SWR means a lot of power is being reflected back toward the transmitter. Solid-state transceivers protect themselves by cutting back their output power when SWR is high. Low SWR is good and would not lower power.
Tip: High SWR? Expect the radio to cut its power.
T7B05
Which of the following might reduce interference by an amateur station to a non-amateur over-the-air radio receiver?
- A. Block the amateur signal with a filter at the antenna input of the affected receiver
- B. Block the interfering signal with a filter on the amateur transmitter
- C. Switch the transmitter from FM to SSB
- D. Switch the transmitter to a narrow-band mode
Show the answer and explanation
Answer: A. Block the amateur signal with a filter at the antenna input of the affected receiver
When a neighbor's receiver is overloaded by your signal, a filter at the affected receiver's antenna input can block your signal from getting in. A filter on the transmitter only helps with unwanted signals like harmonics; it cannot remove your main signal without stopping your transmission.
Tip: Filter the victim's receiver to block your strong signal.
T7B06
Which of the following actions should you take if a neighbor tells you that your station's transmissions are interfering with their radio or TV reception?
- A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel
- B. Immediately turn off your transmitter and contact the nearest FCC office for assistance
- C. Install a harmonic doubler on the output of your transmitter and tune it until the interference is eliminated
- D. All these choices are correct
Show the answer and explanation
Answer: A. Make sure that your station is functioning properly and that it does not cause interference to your own radio or television when it is tuned to the same channel
First check that your own station is working properly and doesn't interfere with your own radio or TV tuned to the same channel. That shows whether the problem is in your station. A 'harmonic doubler' would make interference worse, not better.
Tip: Check your own house first.
T7B07
Which of the following can reduce interference to a 2-meter band transceiver from a nearby commercial FM station?
- A. Installing an RF preamplifier
- B. Using double-shielded coaxial cable
- C. Installing bypass capacitors on the microphone cable
- D. Installing a band-reject filter
Show the answer and explanation
Answer: D. Installing a band-reject filter
A band-reject filter blocks a narrow range of frequencies, such as a strong commercial FM broadcast signal, while letting your 2-meter signals through. A preamplifier would boost the interfering signal too and could make overload worse.
Tip: Reject the band that bothers you.
T7B08
What should you do if something in a neighbor's home is causing harmful interference to your amateur station?
- A. Work with your neighbor to identify the offending device
- B. Politely inform your neighbor that FCC rules prohibit the use of devices that cause interference
- C. Make sure your station meets the standards of good amateur practice
- D. All these choices are correct
Show the answer and explanation
Answer: D. All these choices are correct
If a device in a neighbor's home interferes with your station, work with the neighbor to find it, politely explain that FCC rules prohibit devices that cause harmful interference, and make sure your own station follows good practice. All these choices are correct.
Tip: Be cooperative, polite, and check your own gear.
T7B09
What should be the first step to resolve non-fiber optic cable TV interference caused by your amateur radio transmission?
- A. Add a low-pass filter to the TV antenna input
- B. Add a high-pass filter to the TV antenna input
- C. Add a preamplifier to the TV antenna input
- D. Be sure all TV feed line coaxial connectors are installed properly
Show the answer and explanation
Answer: D. Be sure all TV feed line coaxial connectors are installed properly
Loose or poorly installed coaxial connectors on the TV feed line can let your signal leak into the cable system. Making sure all connectors are installed properly is the first, simplest step. Filters come later if needed.
Tip: Check the connectors before adding filters.
T7B10
What might be a problem if you receive a report that your audio signal through an FM repeater is distorted or unintelligible?
- A. Your transmitter is slightly off frequency
- B. You are speaking too loudly or too close to the microphone
- C. You are in a bad location
- D. All these choices are correct
Show the answer and explanation
Answer: D. All these choices are correct
Distorted audio through a repeater can come from being slightly off frequency, speaking too loudly or too close to the mic, or being in a poor location with a weak signal. All these choices are correct.
Tip: Off frequency, too loud, or bad spot: any can garble you.
T7B11
Which of the following can eliminate distorted voice transmissions?
- A. Adding extra feedline to the antenna to lower SWR
- B. Turning the radio on and off to reset the computer-controlled circuitry
- C. Adding a clip-on ferrite “choke” to the microphone cable to prevent the transmitted signal from feeding back into the transmitter
- D. Turning the squelch control fully clockwise to prevent the transmitted signal from triggering the squelch circuit
Show the answer and explanation
Answer: C. Adding a clip-on ferrite “choke” to the microphone cable to prevent the transmitted signal from feeding back into the transmitter
Sometimes RF from your own transmission travels back along the microphone cable and gets into the radio, distorting your voice. A clip-on ferrite choke on the mic cable blocks that RF. Adding extra feed line or resetting the radio would not fix it.
Tip: Ferrite choke stops RF sneaking back in on the mic cord.
T7C
Antenna and transmission line measurements and troubleshooting: measuring SWR, effects of high SWR, causes of feed line failures; Basic coaxial cable characteristics; Use of dummy loads when testing
T7C01
What is the primary purpose of a dummy load?
- A. To prevent transmitting signals over the air when making tests
- B. To prevent over-modulation of a transmitter
- C. To improve the efficiency of an antenna
- D. To improve the signal-to-noise ratio of a receiver
Show the answer and explanation
Answer: A. To prevent transmitting signals over the air when making tests
A dummy load lets you test a transmitter without sending a signal over the air. It takes in the transmitter's power and turns it into heat instead of radiating it. It does not improve the antenna or the receiver.
Tip: Dummy load: test quietly, no on-air signal.
T7C02
Which of the following is used to determine if an antenna is resonant at the desired operating frequency?
- A. A VTVM
- B. An antenna analyzer
- C. A Q meter
- D. A frequency counter
Show the answer and explanation
Answer: B. An antenna analyzer
An antenna analyzer measures how an antenna behaves at different frequencies, so it can show where the antenna is resonant. A frequency counter only measures the frequency of a signal, not the antenna.
Tip: Analyze your antenna with an antenna analyzer.
T7C03
What does a typical RF dummy load consist of?
- A. A low-voltage power supply and an AC relay
- B. A 50-ohm non-inductive resistor mounted on a heat sink
- C. A low-voltage power supply and a DC relay
- D. A 50-ohm inductive reactance mounted in a shielded enclosure
Show the answer and explanation
Answer: B. A 50-ohm non-inductive resistor mounted on a heat sink
A typical RF dummy load is a 50-ohm resistor that is non-inductive, so it looks like a perfect 50-ohm antenna. It is mounted on a heat sink because it turns the transmitter's power into heat.
Tip: 50 ohms, no inductance, plus a heat sink.
T7C04
What reading on an SWR meter indicates a perfect impedance match between the antenna and the feed line?
- A. 50:50
- B. Zero
- C. 1:1
- D. Full Scale
Show the answer and explanation
Answer: C. 1:1
An SWR of 1:1 means a perfect match between the antenna and the feed line, with no power reflected back. Higher numbers mean a worse match.
Tip: 1:1 is perfect.
T7C05
Why do most solid-state transmitters reduce output power as SWR increases beyond a certain level?
- A. To protect the RF output amplifier transistors
- B. To comply with FCC rules on spectral purity
- C. Because power supplies cannot supply enough current at high SWR
- D. To lower the SWR on the transmission line
Show the answer and explanation
Answer: A. To protect the RF output amplifier transistors
High SWR sends reflected power back into the transmitter, which can overheat and damage its output transistors. Most solid-state radios reduce power automatically to protect those RF output amplifier transistors. Lowering power does not lower the SWR itself.
Tip: Power drops to save the final transistors.
T7C06
What does an SWR reading of 4:1 indicate?
- A. Loss of -4 dB
- B. Good impedance match
- C. Gain of +4 dB
- D. Impedance mismatch
Show the answer and explanation
Answer: D. Impedance mismatch
An SWR of 4:1 is far from the ideal 1:1, so it shows an impedance mismatch between the antenna and the feed line. SWR is a ratio, not a gain or loss in dB.
Tip: Far above 1:1 means mismatch.
T7C07
What happens to power lost in a feed line?
- A. It increases the SWR
- B. It is radiated as harmonics
- C. It is converted into heat
- D. It distorts the signal
Show the answer and explanation
Answer: C. It is converted into heat
Power lost in a feed line is turned into heat in the cable. The loss does not create harmonics or change the SWR.
Tip: Lost power becomes heat.
T7C08
Which instrument can be used to determine SWR?
- A. Voltmeter
- B. Ohmmeter
- C. Iambic pentameter
- D. Directional wattmeter
Show the answer and explanation
Answer: D. Directional wattmeter
A directional wattmeter measures both forward power going to the antenna and reflected power coming back. From those two readings you can find the SWR. A plain voltmeter or ohmmeter can't do this. (Iambic pentameter is poetry, not an instrument.)
Tip: Forward vs. reflected power gives you SWR.
T7C09
Which of the following causes failure of coaxial cables?
- A. Moisture contamination
- B. Solder flux contamination
- C. Rapid fluctuation in transmitter output power
- D. Operation at 100% duty cycle for an extended period
Show the answer and explanation
Answer: A. Moisture contamination
Moisture getting inside coaxial cable is a common cause of failure. Water raises losses and corrodes the conductors and shield over time. Solder flux and normal transmitting do not usually ruin coax.
Tip: Water is coax's worst enemy.
T7C10
Why should the outer jacket of coaxial cable be resistant to ultraviolet light?
- A. Ultraviolet light can increase the resistance of the conductors
- B. Ultraviolet light can increase losses in the cable's jacket
- C. Ultraviolet and RF signals can mix, causing interference
- D. Ultraviolet light can damage the jacket and allow water to enter the cable
Show the answer and explanation
Answer: D. Ultraviolet light can damage the jacket and allow water to enter the cable
Sunlight's ultraviolet (UV) light can break down a cable's outer jacket and make it crack. Once it cracks, water can get in and damage the cable. That is why outdoor coax needs a UV-resistant jacket.
Tip: Sun cracks the jacket, then water gets in.
T7C11
What is an advantage of foam-dielectric versus solid-dielectric coaxial cable?
- A. It is more resistant to moisture contamination
- B. It has higher voltage breakdown
- C. It has less loss per foot
- D. It has a better impedance match to 50 ohms
Show the answer and explanation
Answer: C. It has less loss per foot
Foam-dielectric coax has less loss per foot than solid-dielectric coax, so more of your signal reaches the antenna. The trade-off is that foam can soak up moisture more easily and handles less voltage.
Tip: Foam = lower loss.
T7D
Using basic test instruments: voltmeter, ammeter, and ohmmeter; Soldering
T7D01
Which instrument would you use to measure electric potential?
- A. An ammeter
- B. A voltmeter
- C. A potentiometer
- D. An ohmmeter
Show the answer and explanation
Answer: B. A voltmeter
Electric potential is another name for voltage, and a voltmeter measures voltage. An ammeter measures current and an ohmmeter measures resistance. A potentiometer is a variable resistor, not a meter.
Tip: Potential = volts, so use a voltmeter.
T7D02
How is a voltmeter connected to a component to measure applied voltage?
- A. In series
- B. In parallel
- C. In quadrature
- D. In phase
Show the answer and explanation
Answer: B. In parallel
To measure voltage, connect the voltmeter in parallel, meaning across the two ends of the component. That way the meter sees the same voltage as the part.
Tip: Voltmeter goes across (parallel).
T7D03
When configured to measure current, how is a multimeter connected to a component?
- A. In series
- B. In parallel
- C. In quadrature
- D. In phase
Show the answer and explanation
Answer: A. In series
To measure current, the multimeter must be connected in series so the current flows through the meter. You open the circuit and put the meter in the path.
Tip: Current meter goes in line (series).
T7D04
Which instrument is used to measure electric current?
- A. An ohmmeter
- B. An electrometer
- C. A voltmeter
- D. An ammeter
Show the answer and explanation
Answer: D. An ammeter
An ammeter measures electric current, which is measured in amperes (amps). A voltmeter measures voltage and an ohmmeter measures resistance.
Tip: Ammeter measures amps.
T7D05
How does an ohmmeter measure the resistance of a circuit or component?
- A. By applying a small current and measuring the resulting voltage
- B. By placing a variable resistor in parallel with the circuit
- C. By placing a variable resistor in series with the circuit
- D. By applying a variable voltage and measuring the resulting current change
Show the answer and explanation
Answer: A. By applying a small current and measuring the resulting voltage
An ohmmeter sends a small known current through the part and measures the voltage that results. Using Ohm's law (R = E / I), it works out the resistance.
Tip: Small current in, measure the voltage, compute ohms.
T7D06
Which of the following can damage a multimeter?
- A. Attempting to measure resistance using the voltage setting
- B. Failing to connect one of the probes to ground
- C. Attempting to measure voltage when using the resistance setting
- D. Not allowing it to warm up properly
Show the answer and explanation
Answer: C. Attempting to measure voltage when using the resistance setting
If the meter is set to measure resistance and you connect it to a live voltage, the voltage can damage the meter. In resistance mode the meter uses its own battery and is not built to handle outside voltage. Measuring resistance on the voltage setting just gives a wrong reading.
Tip: Never read volts while on the ohms setting.
T7D07
Which of the following measurements are made using a multimeter?
- A. Signal strength and noise
- B. Impedance and reactance
- C. Voltage and resistance
- D. All these choices are correct
Show the answer and explanation
Answer: C. Voltage and resistance
A multimeter can measure voltage and resistance, and usually current too. It is not used for measuring signal strength, noise, or reactance.
Tip: Multimeter: volts, ohms, amps.
T7D08
Which of the following types of solder should not be used for radio and electronic applications?
- A. Acid-core solder
- B. Lead-tin solder
- C. Rosin-core solder
- D. Tin-copper solder
Show the answer and explanation
Answer: A. Acid-core solder
Acid-core solder should not be used on electronics because the acid flux can corrode wires and circuit parts. Rosin-core solder is the right choice for electronics.
Tip: Acid eats electronics; use rosin core.
T7D09
What is the characteristic appearance of a cold tin-lead solder joint?
- A. Dark black spots
- B. A bright or shiny surface
- C. A rough or lumpy surface
- D. A greenish tinge
Show the answer and explanation
Answer: C. A rough or lumpy surface
A cold solder joint happens when the joint does not get hot enough, and it looks rough or lumpy. A good tin-lead joint is smooth and shiny. Cold joints can make poor or unreliable connections.
Tip: Shiny = good; rough and lumpy = cold joint.
T7D10
What reading indicates that an ohmmeter is connected across a large, discharged capacitor?
- A. Increasing resistance with time
- B. Decreasing resistance with time
- C. Steady full-scale reading
- D. Alternating between open and short circuit
Show the answer and explanation
Answer: A. Increasing resistance with time
When an ohmmeter is connected to a large, discharged capacitor, the meter's current starts charging it. At first the reading is low, then the resistance reading rises over time as the capacitor charges up.
Tip: Charging capacitor: resistance reading climbs.
T7D11
Which of the following precautions should be taken when measuring in-circuit resistance with an ohmmeter?
- A. Ensure that the applied voltages are correct
- B. Ensure that the circuit is not powered
- C. Ensure that the circuit is grounded
- D. Ensure that the circuit is operating at the correct frequency
Show the answer and explanation
Answer: B. Ensure that the circuit is not powered
Before measuring resistance in a circuit, make sure the circuit is not powered. Any voltage in the circuit will throw off the reading and can damage the ohmmeter.
Tip: Power off before you measure ohms.