Ham Tech Prep

Amateur Extra › E9

E9 Antennas and Transmission Lines

93 questions in the pool. Your exam will include 8, one from each group below.

Practice E9 now

E9A

Basic antenna parameters: radiation resistance, gain, beamwidth, efficiency; effective radiated power (ERP) and effective isotropic radiated power (EIRP)

E9A01

What is an isotropic radiator?

  1. A. A calibrated, unidirectional antenna used to make precise antenna gain measurements
  2. B. An omnidirectional, horizontally polarized, precisely calibrated antenna used to make field measurements of antenna gain
  3. C. A hypothetical, lossless antenna having equal radiation intensity in all directions used as a reference for antenna gain
  4. D. A spacecraft antenna used to direct signals toward Earth
Show the answer and explanation

Answer: C. A hypothetical, lossless antenna having equal radiation intensity in all directions used as a reference for antenna gain

An isotropic radiator is an imaginary, lossless antenna that radiates equally in every direction. It is the reference for dBi gain figures.

Tip: Isotropic: imaginary, equal in all directions.

E9A02

What is the effective radiated power (ERP) of a repeater station with 150 watts transmitter power output, 2 dB feed line loss, 2.2 dB duplexer loss, and 7 dBd antenna gain?

  1. A. 469 watts
  2. B. 78.7 watts
  3. C. 420 watts
  4. D. 286 watts
Show the answer and explanation

Answer: D. 286 watts

Net gain = 7 - 2 - 2.2 = +2.8 dB. ERP = 150 W x 10^(2.8/10) = 150 x 1.905 = about 286 W.

Tip: Add gains, subtract losses, then convert dB.

E9A03

What term describing total radiated power takes into account all gains and losses?

  1. A. Power factor
  2. B. Half-power bandwidth
  3. C. Effective radiated power
  4. D. Apparent power
Show the answer and explanation

Answer: C. Effective radiated power

Effective radiated power is transmitter power adjusted for all feed line losses and antenna gain. It describes the power actually radiated in the favored direction.

Tip: ERP counts all gains and losses.

E9A04

Which of the following factors affect the feed point impedance of an antenna?

  1. A. Transmission line length
  2. B. Antenna height
  3. C. The settings of an antenna tuner at the transmitter
  4. D. The input power level
Show the answer and explanation

Answer: B. Antenna height

Antenna height changes how the antenna couples to the ground beneath it, which changes its feed point impedance. Feed line length and tuner settings do not change the antenna itself.

Tip: Height changes feed point impedance.

E9A05

What does the term “ground gain” mean?

  1. A. The change in signal strength caused by grounding the antenna
  2. B. The gain of the antenna with respect to a dipole at ground level
  3. C. To force net gain to 0 dB by grounding part of the antenna
  4. D. An increase in signal strength from ground reflections in the environment of the antenna
Show the answer and explanation

Answer: D. An increase in signal strength from ground reflections in the environment of the antenna

Ground gain is the boost in signal strength from radio waves reflecting off the ground near the antenna. Reflections add in phase at certain angles.

Tip: Ground reflections add ground gain.

E9A06

What is the effective radiated power (ERP) of a repeater station with 200 watts transmitter power output, 4 dB feed line loss, 3.2 dB duplexer loss, 0.8 dB circulator loss, and 10 dBd antenna gain?

  1. A. 317 watts
  2. B. 2,000 watts
  3. C. 126 watts
  4. D. 300 watts
Show the answer and explanation

Answer: A. 317 watts

Net gain = 10 - 4 - 3.2 - 0.8 = +2 dB. ERP = 200 W x 10^(2/10) = 200 x 1.585 = about 317 W.

Tip: Net +2 dB is about 1.58 times.

E9A07

What is the effective isotropic radiated power (EIRP) of a repeater station with 200 watts transmitter power output, 2 dB feed line loss, 2.8 dB duplexer loss, 1.2 dB circulator loss, and 7 dBi antenna gain?

  1. A. 159 watts
  2. B. 252 watts
  3. C. 632 watts
  4. D. 63.2 watts
Show the answer and explanation

Answer: B. 252 watts

Net gain = 7 - 2 - 2.8 - 1.2 = +1 dB. EIRP = 200 W x 10^(1/10) = 200 x 1.259 = about 252 W.

Tip: Net +1 dB is about 1.26 times.

E9A08

Which frequency band has the smallest first Fresnel zone?

  1. A. 5.8 GHz
  2. B. 3.4 GHz
  3. C. 2.4 GHz
  4. D. 900 MHz
Show the answer and explanation

Answer: A. 5.8 GHz

Fresnel zone size shrinks as wavelength gets shorter. The highest frequency listed, 5.8 GHz, has the shortest wavelength and the smallest zone.

Tip: Higher frequency, smaller Fresnel zone.

E9A09

What is antenna efficiency?

  1. A. Radiation resistance divided by transmission resistance
  2. B. Radiation resistance divided by total resistance
  3. C. Total resistance divided by radiation resistance
  4. D. Effective radiated power divided by transmitter output
Show the answer and explanation

Answer: B. Radiation resistance divided by total resistance

Antenna efficiency is radiation resistance divided by total resistance. Total resistance includes losses, so more loss means lower efficiency.

Tip: Efficiency = R radiation / R total.

E9A10

Which of the following improves the efficiency of a ground-mounted quarter-wave vertical antenna?

  1. A. Installing a ground radial system
  2. B. Isolating the coax shield from ground
  3. C. Shortening the radiating element
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. Installing a ground radial system

A ground-mounted vertical loses power in the soil. A system of ground radials gives a low-loss return path and improves efficiency.

Tip: More radials, less ground loss.

E9A11

Which of the following determines ground losses for a ground-mounted vertical antenna operating on HF?

  1. A. The standing wave ratio
  2. B. Distance from the transmitter
  3. C. Soil conductivity
  4. D. Take-off angle
Show the answer and explanation

Answer: C. Soil conductivity

Ground losses depend mostly on how well the soil conducts. Poor soil conductivity wastes more power as heat.

Tip: Soil conductivity sets ground loss.

E9A12

How much gain does an antenna have compared to a half-wavelength dipole if it has 6 dB gain over an isotropic radiator?

  1. A. 3.85 dB
  2. B. 6.0 dB
  3. C. 8.15 dB
  4. D. 2.79 dB
Show the answer and explanation

Answer: A. 3.85 dB

A dipole has 2.15 dB gain over isotropic. dBd = dBi - 2.15 = 6 - 2.15 = 3.85 dB.

Tip: dBd = dBi - 2.15.

E9B

Antenna patterns and designs: azimuth and elevation patterns; gain as a function of pattern; antenna modeling

E9B01

What is the 3 dB beamwidth of the antenna radiation pattern shown in Figure E9-1?

Figure E9-1 from the question pool

  1. A. 75 degrees
  2. B. 50 degrees
  3. C. 25 degrees
  4. D. 30 degrees
Show the answer and explanation

Answer: B. 50 degrees

Beamwidth is measured between the points where the main lobe is 3 dB down from its peak. In Figure E9-1 those points are about 25 degrees either side, for a total of 50 degrees.

Tip: Measure between the -3 dB points.

E9B02

What is the front-to-back ratio of the antenna radiation pattern shown in Figure E9-1?

Figure E9-1 from the question pool

  1. A. 36 dB
  2. B. 14 dB
  3. C. 24 dB
  4. D. 18 dB
Show the answer and explanation

Answer: D. 18 dB

Front-to-back ratio compares the main lobe to the signal directly behind the antenna. In Figure E9-1 the rear lobe is about 18 dB below the front.

Tip: Front vs. directly behind.

E9B03

What is the front-to-side ratio of the antenna radiation pattern shown in Figure E9-1?

Figure E9-1 from the question pool

  1. A. 12 dB
  2. B. 24 dB
  3. C. 18 dB
  4. D. 14 dB
Show the answer and explanation

Answer: D. 14 dB

Front-to-side ratio compares the main lobe with the signal 90 degrees off to the side. In Figure E9-1 the side response is about 14 dB down.

Tip: Front vs. 90 degrees off.

E9B04

What is the front-to-back ratio of the radiation pattern shown in Figure E9-2?

Figure E9-2 from the question pool

  1. A. 15 dB
  2. B. 28 dB
  3. C. 3 dB
  4. D. 38 dB
Show the answer and explanation

Answer: B. 28 dB

In Figure E9-2 the main lobe is at 0 dB and the strongest response toward the rear is about 28 dB down. That gives a 28 dB front-to-back ratio.

Tip: Compare main lobe peak to rear.

E9B05

What type of antenna pattern is shown in Figure E9-2?

Figure E9-2 from the question pool

  1. A. Elevation
  2. B. Azimuth
  3. C. Near field
  4. D. Polarization
Show the answer and explanation

Answer: A. Elevation

Figure E9-2 shows radiation versus angle above the horizon, from ground level up to overhead. That is an elevation pattern; an azimuth pattern shows compass directions.

Tip: Angles above horizon = elevation pattern.

E9B06

What is the elevation angle of peak response in the antenna radiation pattern shown in Figure E9-2?

Figure E9-2 from the question pool

  1. A. 45 degrees
  2. B. 75 degrees
  3. C. 7.5 degrees
  4. D. 25 degrees
Show the answer and explanation

Answer: C. 7.5 degrees

In Figure E9-2 the main lobe peaks at a low angle of about 7.5 degrees above the horizon. Low angles are good for long-distance HF contacts.

Tip: Peak lobe is low, 7.5 degrees.

E9B07

What is the difference in radiated power between a lossless antenna with gain and an isotropic radiator driven by the same power?

  1. A. The power radiated from the directional antenna is increased by the gain of the antenna
  2. B. The power radiated from the directional antenna is stronger by its front-to-back ratio
  3. C. They are the same
  4. D. The power radiated from the isotropic radiator is 2.15 dB greater than that from the directional antenna
Show the answer and explanation

Answer: C. They are the same

A lossless antenna cannot create power; gain only concentrates power in some directions at the expense of others. The total radiated power is the same as the isotropic radiator.

Tip: Gain redirects power; it does not create it.

E9B08

What is the far field of an antenna?

  1. A. The region of the ionosphere where radiated power is not refracted
  2. B. The region where radiated power dissipates over a specified time period
  3. C. The region where radiated field strengths are constant
  4. D. The region where the shape of the radiation pattern no longer varies with distance
Show the answer and explanation

Answer: D. The region where the shape of the radiation pattern no longer varies with distance

The far field is the region where the shape of the radiation pattern stays the same no matter how much farther away you go. Closer in, in the near field, the pattern shape still changes.

Tip: Far field: pattern shape stops changing.

E9B09

What type of analysis is commonly used for modeling antennas?

  1. A. Graphical analysis
  2. B. Method of Moments
  3. C. Mutual impedance analysis
  4. D. Calculus differentiation with respect to physical properties
Show the answer and explanation

Answer: B. Method of Moments

Antenna modeling programs like NEC use the Method of Moments. It calculates currents along the antenna wires to predict patterns and impedance.

Tip: NEC modeling = Method of Moments.

E9B10

What is the principle of a Method of Moments analysis?

  1. A. A wire is modeled as a series of segments, each having a uniform value of current
  2. B. A wire is modeled as a single sine-wave current generator
  3. C. A wire is modeled as a single sine-wave voltage source
  4. D. A wire is modeled as a series of segments, each having a distinct value of voltage across it
Show the answer and explanation

Answer: A. A wire is modeled as a series of segments, each having a uniform value of current

Method of Moments divides each wire into short segments, each assumed to carry a uniform current. The results from all segments are combined to model the antenna.

Tip: Segments, each with uniform current.

E9B11

What is a disadvantage of decreasing the number of wire segments in an antenna model below 10 segments per half-wavelength?

  1. A. Ground conductivity will not be accurately modeled
  2. B. The resulting design will favor radiation of harmonic energy
  3. C. The computed feed point impedance may be incorrect
  4. D. The antenna will become mechanically unstable
Show the answer and explanation

Answer: C. The computed feed point impedance may be incorrect

Too few segments gives a coarse model of the current distribution. The computed feed point impedance may then be wrong.

Tip: Too few segments, wrong impedance.

E9C

Practical wire antennas; folded dipoles; phased arrays; effects of ground near antennas

E9C01

What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed 180 degrees out of phase?

  1. A. Cardioid
  2. B. Omni-directional
  3. C. A figure-eight broadside to the axis of the array
  4. D. A figure-eight oriented along the axis of the array
Show the answer and explanation

Answer: D. A figure-eight oriented along the axis of the array

Two verticals a half wavelength apart fed 180 degrees out of phase reinforce along the line joining them and cancel broadside. The result is an end-fire figure-eight along the array axis.

Tip: Half wave, out of phase: end-fire figure-eight.

E9C02

What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/4-wavelength apart and fed 90 degrees out of phase?

  1. A. Cardioid
  2. B. A figure-eight end-fire along the axis of the array
  3. C. A figure-eight broadside to the axis of the array
  4. D. Omni-directional
Show the answer and explanation

Answer: A. Cardioid

Quarter-wave spacing with 90 degree phasing makes signals add in one direction and cancel in the opposite direction. That produces a heart-shaped cardioid pattern.

Tip: Quarter wave, 90 degrees = cardioid.

E9C03

What type of radiation pattern is created by two 1/4-wavelength vertical antennas spaced 1/2-wavelength apart and fed in phase?

  1. A. Omni-directional
  2. B. Cardioid
  3. C. A figure-eight broadside to the axis of the array
  4. D. A figure-eight end-fire along the axis of the array
Show the answer and explanation

Answer: C. A figure-eight broadside to the axis of the array

Two verticals a half wavelength apart fed in phase add broadside to the array and cancel along its axis. The pattern is a figure-eight broadside to the array.

Tip: Half wave, in phase: broadside figure-eight.

E9C04

What happens to the radiation pattern of an unterminated long wire antenna as the wire length is increased?

  1. A. Fewer lobes form with the major lobes increasing closer to broadside to the wire
  2. B. Additional lobes form with major lobes increasingly aligned with the axis of the antenna
  3. C. The elevation angle increases, and the front-to-rear ratio decreases
  4. D. The elevation angle increases, while the front-to-rear ratio is unaffected
Show the answer and explanation

Answer: B. Additional lobes form with major lobes increasingly aligned with the axis of the antenna

As a long wire gets longer, it forms more lobes. The main lobes swing closer to the direction of the wire itself.

Tip: Longer wire, lobes move toward the wire.

E9C05

What is the purpose of feeding an off-center-fed dipole (OCFD) between the center and one end instead of at the midpoint?

  1. A. To create a similar feed point impedance on multiple bands
  2. B. To suppress off-center lobes at higher frequencies
  3. C. To resonate the antenna across a wider range of frequencies
  4. D. To reduce common-mode current coupling on the feed line shield
Show the answer and explanation

Answer: A. To create a similar feed point impedance on multiple bands

Feeding a dipole off center finds a point where the impedance is similar on several bands. That lets one antenna work multiple bands with one feed line.

Tip: Off-center feed: similar impedance on several bands.

E9C06

What is the effect of adding a terminating resistor to a rhombic or long-wire antenna?

  1. A. It reflects the standing waves on the antenna elements back to the transmitter
  2. B. It changes the radiation pattern from bidirectional to unidirectional
  3. C. It changes the radiation pattern from horizontal to vertical polarization
  4. D. It decreases the ground loss
Show the answer and explanation

Answer: B. It changes the radiation pattern from bidirectional to unidirectional

A terminating resistor absorbs the wave that would otherwise reflect from the far end. This removes the rear lobe and makes the pattern unidirectional.

Tip: Terminate it to make it one-way.

E9C07

What is the approximate feed point impedance at the center of a two-wire half-wave folded dipole antenna?

  1. A. 300 ohms
  2. B. 72 ohms
  3. C. 50 ohms
  4. D. 450 ohms
Show the answer and explanation

Answer: A. 300 ohms

A folded dipole has about four times the impedance of a regular dipole. 4 x 72 ohms is close to 300 ohms.

Tip: Folded dipole = 300 ohms.

E9C08

What is a folded dipole antenna?

  1. A. A dipole one-quarter wavelength long
  2. B. A center-fed dipole with the ends folded down 90 degrees at the midpoint of each side
  3. C. A half-wave dipole with an additional parallel wire connecting its two ends
  4. D. A dipole configured to provide forward gain
Show the answer and explanation

Answer: C. A half-wave dipole with an additional parallel wire connecting its two ends

A folded dipole is a half-wave dipole with a second parallel wire joining its two ends. It forms a long, narrow loop.

Tip: Folded dipole: two parallel wires joined at ends.

E9C09

Which of the following describes a G5RV antenna?

  1. A. A wire antenna center-fed through a specific length of open-wire line connected to a balun and coaxial feed line
  2. B. A multi-band trap antenna
  3. C. A phased array antenna consisting of multiple loops
  4. D. A wide band dipole using shorted coaxial cable for the radiating elements and fed with a 4:1 balun
Show the answer and explanation

Answer: A. A wire antenna center-fed through a specific length of open-wire line connected to a balun and coaxial feed line

The G5RV is a center-fed wire antenna. It uses a specific length of open-wire line, then a balun and coax to the radio.

Tip: G5RV: wire, ladder line section, then coax.

E9C10

Which of the following describes a Zepp antenna?

  1. A. A horizontal array capable of quickly changing the direction of maximum radiation by changing phasing lines
  2. B. An end-fed half-wavelength dipole
  3. C. An omni-directional antenna commonly used for satellite communications
  4. D. A vertical array capable of quickly changing the direction of maximum radiation by changing phasing lines
Show the answer and explanation

Answer: B. An end-fed half-wavelength dipole

A Zepp antenna is a half-wave dipole fed at one end. The name comes from its use on Zeppelin airships.

Tip: Zepp = end-fed half wave.

E9C11

How is the far-field elevation pattern of a vertically polarized antenna affected by being mounted over seawater versus soil?

  1. A. Radiation at low angles decreases
  2. B. Additional lobes appear at higher elevation angles
  3. C. Separate elevation lobes will combine into a single lobe
  4. D. Radiation at low angles increases
Show the answer and explanation

Answer: D. Radiation at low angles increases

Seawater is an excellent conductor, so it reflects much better than soil. A vertical antenna over seawater radiates more strongly at low angles.

Tip: Over saltwater, low angles get stronger.

E9C12

Which of the following describes an extended double Zepp antenna?

  1. A. An end-fed full-wave dipole antenna
  2. B. A center-fed 1.5-wavelength dipole antenna
  3. C. A center-fed 1.25-wavelength dipole antenna
  4. D. An end-fed 2-wavelength dipole antenna
Show the answer and explanation

Answer: C. A center-fed 1.25-wavelength dipole antenna

An extended double Zepp is a center-fed dipole about 1.25 wavelengths long. The extra length gives it more gain than a half-wave dipole.

Tip: Extended double Zepp = 1.25 wavelengths, center-fed.

E9C13

How does the radiation pattern of a horizontally polarized antenna vary with increasing height above ground?

  1. A. The takeoff angle of the lowest elevation lobe increases
  2. B. The takeoff angle of the lowest elevation lobe decreases
  3. C. The horizontal beamwidth increases
  4. D. The horizontal beamwidth decreases
Show the answer and explanation

Answer: B. The takeoff angle of the lowest elevation lobe decreases

Raising a horizontal antenna higher above ground lowers the takeoff angle of its lowest lobe. Lower angles favor long-distance contacts.

Tip: Higher antenna, lower takeoff angle.

E9C14

How does the radiation pattern of a horizontally-polarized antenna mounted above a long slope compare with the same antenna mounted above flat ground?

  1. A. The main lobe takeoff angle increases in the downhill direction
  2. B. The main lobe takeoff angle decreases in the downhill direction
  3. C. The horizontal beamwidth decreases in the downhill direction
  4. D. The horizontal beamwidth increases in the uphill direction
Show the answer and explanation

Answer: B. The main lobe takeoff angle decreases in the downhill direction

A slope tilts the effective ground plane. In the downhill direction the main lobe's takeoff angle is lower than over flat ground.

Tip: Downhill, lower takeoff angle.

E9D

Yagi antennas; parabolic reflectors; feed point impedance and loading of electrically short antennas; antenna Q; RF grounding

E9D01

How much does the gain of an ideal parabolic reflector antenna increase when the operating frequency is doubled?

  1. A. 2 dB
  2. B. 3 dB
  3. C. 4 dB
  4. D. 6 dB
Show the answer and explanation

Answer: D. 6 dB

Dish gain rises with the square of frequency. Doubling frequency gives 2^2 = 4 times the gain, and 10 x log(4) = 6 dB.

Tip: Double frequency, add 6 dB.

E9D02

How can two linearly polarized Yagi antennas be used to produce circular polarization?

  1. A. Stack two Yagis to form an array with the respective elements in parallel planes fed 90 degrees out of phase
  2. B. Stack two Yagis to form an array with the respective elements in parallel planes fed in phase
  3. C. Arrange two Yagis on the same axis and perpendicular to each other with the driven elements at the same point on the boom and fed 90 degrees out of phase
  4. D. Arrange two Yagis collinear to each other with the driven elements fed 180 degrees out of phase
Show the answer and explanation

Answer: C. Arrange two Yagis on the same axis and perpendicular to each other with the driven elements at the same point on the boom and fed 90 degrees out of phase

Mount two Yagis on the same boom at right angles to each other, with driven elements at the same point. Feed them 90 degrees out of phase to get circular polarization.

Tip: Crossed Yagis, 90 degrees phase = circular.

E9D03

What is the most efficient location for a loading coil on an electrically short whip?

  1. A. Near the center of the vertical radiator
  2. B. As low as possible on the vertical radiator
  3. C. At a voltage maximum
  4. D. At a voltage null
Show the answer and explanation

Answer: A. Near the center of the vertical radiator

A loading coil near the center of a short whip keeps more current flowing in the lower part of the antenna. That makes it the most efficient location.

Tip: Center loading is most efficient.

E9D04

Why should antenna loading coils have a high ratio of reactance to resistance?

  1. A. To swamp out harmonics
  2. B. To lower the radiation angle
  3. C. To maximize efficiency
  4. D. To minimize the Q
Show the answer and explanation

Answer: C. To maximize efficiency

A high ratio of reactance to resistance means a high-Q coil with little loss. Less loss in the coil means better antenna efficiency.

Tip: Low-loss coil = high efficiency.

E9D05

Approximately how long is a Yagi's driven element?

  1. A. 234 divided by frequency in MHz
  2. B. 1005 divided by frequency in MHz
  3. C. 1/4 wavelength
  4. D. 1/2 wavelength
Show the answer and explanation

Answer: D. 1/2 wavelength

The driven element of a Yagi is about a half wavelength long, like a dipole. The formula 468/f gives that length in feet; 234/f gives a quarter wave.

Tip: Yagi driven element = half wave.

E9D06

What happens to SWR bandwidth when one or more loading coils are used to resonate an electrically short antenna?

  1. A. It is increased
  2. B. It is decreased
  3. C. It is unchanged if the loading coil is located at the feed point
  4. D. It is unchanged if the loading coil is located at a voltage maximum point
Show the answer and explanation

Answer: B. It is decreased

Loading coils make a short antenna resonant but raise its Q. Higher Q means the SWR stays low over a narrower range, so bandwidth decreases.

Tip: Loading coil narrows SWR bandwidth.

E9D07

What is an advantage of top loading an electrically short HF vertical antenna?

  1. A. Lower Q
  2. B. Greater structural strength
  3. C. Higher losses
  4. D. Improved radiation efficiency
Show the answer and explanation

Answer: D. Improved radiation efficiency

Top loading, such as a capacitance hat, spreads current more evenly up the vertical. This raises radiation resistance and improves efficiency.

Tip: Top hat improves efficiency.

E9D08

What happens as the Q of an antenna increases?

  1. A. SWR bandwidth increases
  2. B. SWR bandwidth decreases
  3. C. Gain is reduced
  4. D. More common-mode current is present on the feed line
Show the answer and explanation

Answer: B. SWR bandwidth decreases

Higher Q means a sharper resonance. The SWR rises quickly off frequency, so SWR bandwidth decreases.

Tip: High Q, narrow bandwidth.

E9D09

What is the function of a loading coil in an electrically short antenna?

  1. A. To increase the SWR bandwidth by increasing net reactance
  2. B. To lower the losses
  3. C. To lower the Q
  4. D. To resonate the antenna by cancelling the capacitive reactance
Show the answer and explanation

Answer: D. To resonate the antenna by cancelling the capacitive reactance

A short antenna looks capacitive. A loading coil adds inductive reactance that cancels it, making the antenna resonant.

Tip: Coil cancels capacitive reactance.

E9D10

How does radiation resistance of a base-fed whip antenna change below its resonant frequency?

  1. A. Radiation resistance increases
  2. B. Radiation resistance decreases
  3. C. Radiation resistance becomes imaginary
  4. D. Radiation resistance does not depend on frequency
Show the answer and explanation

Answer: B. Radiation resistance decreases

Below resonance a whip is electrically short. Radiation resistance drops quickly as the antenna gets shorter compared to a wavelength.

Tip: Shorter antenna, lower radiation resistance.

E9D11

Why do most two-element Yagis with normal spacing have a reflector instead of a director?

  1. A. Lower SWR
  2. B. Higher receiving directivity factor
  3. C. Greater front-to-side
  4. D. Higher gain
Show the answer and explanation

Answer: D. Higher gain

With normal spacing, a driven element plus reflector gives somewhat more gain than a driven element plus director. That is why most two-element Yagis use a reflector.

Tip: Two elements: reflector gives more gain.

E9D12

What is the purpose of making a Yagi's parasitic elements either longer or shorter than resonance?

  1. A. Wind torque cancellation
  2. B. Mechanical balance
  3. C. Control of phase shift
  4. D. Minimize losses
Show the answer and explanation

Answer: C. Control of phase shift

Making parasitic elements longer or shorter than resonance controls the phase of their currents. That phase sets whether they act as reflectors or directors.

Tip: Element length sets phase.

E9E

Impedance matching: matching antennas to feed lines; phasing lines; power dividers

E9E01

Which matching system for Yagi antennas requires the driven element to be insulated from the boom?

  1. A. Gamma
  2. B. Beta or hairpin
  3. C. Shunt-fed
  4. D. T-match
Show the answer and explanation

Answer: B. Beta or hairpin

The beta or hairpin match feeds the driven element at its center, which must be split and insulated from the boom. Gamma and T matches can attach to a grounded element.

Tip: Hairpin needs an insulated, split element.

E9E02

What antenna matching system matches coaxial cable to an antenna by connecting the shield to the center of the antenna and the conductor a fraction of a wavelength to one side?

  1. A. Gamma match
  2. B. Delta match
  3. C. T-match
  4. D. Stub match
Show the answer and explanation

Answer: A. Gamma match

The gamma match connects the coax shield to the center of the element and the center conductor to a point out along one side. It is common on Yagis.

Tip: Gamma: shield center, conductor off to one side.

E9E03

What matching system uses a short length of transmission line connected in parallel with the feed line at or near the feed point?

  1. A. Gamma match
  2. B. Delta match
  3. C. T-match
  4. D. Stub match
Show the answer and explanation

Answer: D. Stub match

A stub match uses a short length of transmission line connected in parallel with the feed line near the load. The stub's reactance cancels mismatch.

Tip: Stub = parallel piece of line.

E9E04

What is the purpose of the series capacitor in a gamma match?

  1. A. To provide DC isolation between the feed line and the antenna
  2. B. To cancel unwanted inductive reactance
  3. C. To provide a rejection notch that prevents the radiation of harmonics
  4. D. To transform the antenna impedance to a higher value
Show the answer and explanation

Answer: B. To cancel unwanted inductive reactance

The gamma rod adds inductive reactance. A series capacitor cancels that inductive reactance so the match is purely resistive.

Tip: Gamma capacitor cancels inductance.

E9E05

What Yagi driven element feed point impedance is required to use a beta or hairpin matching system?

  1. A. Capacitive (driven element electrically shorter than 1/2 wavelength)
  2. B. Inductive (driven element electrically longer than 1/2 wavelength)
  3. C. Purely resistive
  4. D. Purely reactive
Show the answer and explanation

Answer: A. Capacitive (driven element electrically shorter than 1/2 wavelength)

The hairpin acts as an inductor across the feed point. It needs a capacitive feed point, so the driven element is made a little shorter than a half wavelength.

Tip: Hairpin needs a slightly short, capacitive element.

E9E06

Which of these transmission line impedances would be suitable for constructing a quarter-wave Q-section for matching a 100-ohm feed point impedance to a 50-ohm transmission line?

  1. A. 50 ohms
  2. B. 62 ohms
  3. C. 75 ohms
  4. D. 90 ohms
Show the answer and explanation

Answer: C. 75 ohms

Q-section impedance = square root of (Z1 x Z2) = sqrt(50 x 100) = 70.7 ohms. Common 75-ohm coax is the closest choice.

Tip: Q-section: square root of Z1 x Z2.

E9E07

What parameter describes the interaction of a load and transmission line?

  1. A. Characteristic impedance
  2. B. Reflection coefficient
  3. C. Velocity factor
  4. D. Dielectric constant
Show the answer and explanation

Answer: B. Reflection coefficient

The reflection coefficient describes how much of the wave is reflected where the line meets the load. It depends on both the load and line impedance.

Tip: Reflection coefficient: line meets load.

E9E08

What is a use for a Wilkinson divider?

  1. A. To divide the operating frequency of a transmitter signal so it can be used on a lower frequency band
  2. B. To feed high-impedance antennas from a low-impedance source
  3. C. To divide power equally between two 50-ohm loads while maintaining 50-ohm input impedance
  4. D. To divide the frequency of the input to a counter to increase its frequency range
Show the answer and explanation

Answer: C. To divide power equally between two 50-ohm loads while maintaining 50-ohm input impedance

A Wilkinson divider splits power equally between two 50-ohm loads. It still presents a 50-ohm input impedance and isolates the outputs.

Tip: Wilkinson: equal split, still 50 ohms.

E9E09

Which of the following is used to shunt feed a grounded tower at its base?

  1. A. Double-bazooka match
  2. B. Beta or hairpin match
  3. C. Gamma match
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. Gamma match

A grounded tower can be shunt fed with a gamma match, which taps up the tower from its base. The base stays grounded.

Tip: Shunt feed a tower with a gamma.

E9E11

What is the purpose of using multiple driven elements connected through phasing lines?

  1. A. To control the antenna's radiation pattern
  2. B. To prevent harmonic radiation from the transmitter
  3. C. To allow single-band antennas to operate on other bands
  4. D. To create a low-angle radiation pattern
Show the answer and explanation

Answer: A. To control the antenna's radiation pattern

Feeding several driven elements through phasing lines controls how their signals add and cancel. That shapes the antenna's radiation pattern.

Tip: Phasing lines steer the pattern.

E9F

Transmission lines: characteristics of open and shorted feed lines; coax versus open wire; velocity factor; electrical length; coaxial cable dielectrics; microstrip

E9F01

What is the velocity factor of a transmission line?

  1. A. The ratio of its characteristic impedance to its termination impedance
  2. B. The ratio of its termination impedance to its characteristic impedance
  3. C. The velocity of a wave in the transmission line multiplied by the velocity of light in a vacuum
  4. D. The velocity of a wave in the transmission line divided by the velocity of light in a vacuum
Show the answer and explanation

Answer: D. The velocity of a wave in the transmission line divided by the velocity of light in a vacuum

Velocity factor is the speed of a wave in the line divided by the speed of light in a vacuum. It is always less than 1.

Tip: VF = line speed / light speed.

E9F02

Which of the following has the biggest effect on the velocity factor of a transmission line?

  1. A. The characteristic impedance
  2. B. The transmission line length
  3. C. The insulating dielectric material
  4. D. The center conductor resistivity
Show the answer and explanation

Answer: C. The insulating dielectric material

The insulating dielectric between conductors mostly sets how fast waves travel in the line. Line length and conductor resistance do not change velocity factor.

Tip: Dielectric sets velocity factor.

E9F03

Why is the electrical length of a coaxial cable longer than its physical length?

  1. A. Skin effect is less pronounced in the coaxial cable
  2. B. Skin effect is more pronounced in the coaxial cable
  3. C. Electromagnetic waves move faster in coaxial cable than in air
  4. D. Electromagnetic waves move more slowly in a coaxial cable than in air
Show the answer and explanation

Answer: D. Electromagnetic waves move more slowly in a coaxial cable than in air

Waves move more slowly in coax than in air, so more wavelengths fit in a given length. Electrically the cable is longer than it physically is.

Tip: Slower in coax, so electrically longer.

E9F04

What impedance does a 1/2-wavelength transmission line present to an RF generator when the line is shorted at the far end?

  1. A. Very high impedance
  2. B. Very low impedance
  3. C. The same as the characteristic impedance of the line
  4. D. The same as the output impedance of the RF generator
Show the answer and explanation

Answer: B. Very low impedance

A half-wave line repeats its load impedance at the input. A short at the far end looks like a short, very low impedance, at the generator.

Tip: Half wave repeats the load.

E9F05

What is microstrip?

  1. A. Special shielding material designed for microwave frequencies
  2. B. Miniature coax used for low power applications
  3. C. Short lengths of coax mounted on printed circuit boards to minimize time delay between microwave circuits
  4. D. Precision printed circuit conductors above a ground plane that provide constant impedance interconnects at microwave frequencies
Show the answer and explanation

Answer: D. Precision printed circuit conductors above a ground plane that provide constant impedance interconnects at microwave frequencies

Microstrip is a precise printed circuit trace over a ground plane. It acts as a constant-impedance transmission line at microwave frequencies.

Tip: Microstrip = PCB trace over ground plane.

E9F06

What is the approximate physical length of an air-insulated, parallel conductor transmission line that is electrically 1/2 wavelength long at 14.10 MHz?

  1. A. 7.0 meters
  2. B. 8.5 meters
  3. C. 10.6 meters
  4. D. 13.3 meters
Show the answer and explanation

Answer: C. 10.6 meters

Wavelength = 300 / 14.10 MHz = 21.28 m, so half is about 10.64 m. Air-insulated line has a velocity factor near 1, so the length is about 10.6 m.

Tip: Half wave in meters = 150 / MHz.

E9F07

How does parallel conductor transmission line compare to coaxial cable with a plastic dielectric?

  1. A. Lower loss
  2. B. Higher SWR
  3. C. Smaller reflection coefficient
  4. D. Lower velocity factor
Show the answer and explanation

Answer: A. Lower loss

Parallel conductor line, such as ladder line, has much lower loss than plastic-dielectric coax. Most of its dielectric is air.

Tip: Ladder line = lower loss.

E9F08

Which of the following is a significant difference between foam dielectric coaxial cable and solid dielectric coaxial cable, assuming all other parameters are the same?

  1. A. Foam dielectric coaxial cable has lower safe maximum operating voltage
  2. B. Foam dielectric coaxial cable has lower loss per unit of length
  3. C. Foam dielectric coaxial cable has higher velocity factor
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Foam dielectric has more air, so it has lower loss and higher velocity factor. It also withstands less voltage than solid dielectric. All three statements are true.

Tip: Foam: less loss, faster, lower voltage rating.

E9F09

What impedance does a 1/4-wavelength transmission line present to an RF generator when the line is shorted at the far end?

  1. A. Very high impedance
  2. B. Very low impedance
  3. C. The same as the characteristic impedance of the transmission line
  4. D. The same as the generator output impedance
Show the answer and explanation

Answer: A. Very high impedance

A quarter-wave line inverts the load impedance. A short at the far end appears as a very high impedance at the input.

Tip: Quarter wave flips short to open.

E9F10

What impedance does a 1/8-wavelength transmission line present to an RF generator when the line is shorted at the far end?

  1. A. A capacitive reactance
  2. B. The same as the characteristic impedance of the line
  3. C. An inductive reactance
  4. D. Zero
Show the answer and explanation

Answer: C. An inductive reactance

A shorted line shorter than a quarter wave looks inductive at the input. At 1/8 wave, it is an inductive reactance.

Tip: Short and short line = inductor.

E9F11

What impedance does a 1/8-wavelength transmission line present to an RF generator when the line is open at the far end?

  1. A. The same as the characteristic impedance of the line
  2. B. An inductive reactance
  3. C. A capacitive reactance
  4. D. Infinite
Show the answer and explanation

Answer: C. A capacitive reactance

An open line shorter than a quarter wave looks capacitive at the input. At 1/8 wave, it is a capacitive reactance.

Tip: Open and short line = capacitor.

E9F12

What impedance does a 1/4-wavelength transmission line present to an RF generator when the line is open at the far end?

  1. A. The same as the characteristic impedance of the line
  2. B. The same as the input impedance to the generator
  3. C. Very high impedance
  4. D. Very low impedance
Show the answer and explanation

Answer: D. Very low impedance

A quarter-wave line inverts the load. An open at the far end appears as a very low impedance, like a short, at the input.

Tip: Quarter wave flips open to short.

E9G

The Smith chart

E9G01

Which of the following can be calculated using a Smith chart?

  1. A. Impedance along transmission lines
  2. B. Radiation resistance
  3. C. Antenna radiation pattern
  4. D. Radio propagation
Show the answer and explanation

Answer: A. Impedance along transmission lines

A Smith chart is a graphical tool for working with impedance. It shows how impedance changes along a transmission line.

Tip: Smith chart = impedance on lines.

E9G02

What type of coordinate system is used in a Smith chart?

  1. A. Voltage circles and current arcs
  2. B. Resistance circles and reactance arcs
  3. C. Voltage chords and current chords
  4. D. Resistance lines and reactance chords
Show the answer and explanation

Answer: B. Resistance circles and reactance arcs

The Smith chart is built from circles of constant resistance and arcs of constant reactance. Their crossings mark impedance values.

Tip: Resistance circles, reactance arcs.

E9G03

Which of the following is often determined using a Smith chart?

  1. A. Beam headings and radiation patterns
  2. B. Satellite azimuth and elevation bearings
  3. C. Impedance and SWR values in transmission lines
  4. D. Point-to-point propagation reliability as a function of frequency
Show the answer and explanation

Answer: C. Impedance and SWR values in transmission lines

Smith charts are used to find impedance and SWR along transmission lines. They are not used for antenna patterns or propagation.

Tip: Smith chart: impedance and SWR.

E9G04

What are the two families of circles and arcs that make up a Smith chart?

  1. A. Inductance and capacitance
  2. B. Reactance and voltage
  3. C. Resistance and reactance
  4. D. Voltage and impedance
Show the answer and explanation

Answer: C. Resistance and reactance

The two families of curves on a Smith chart are resistance circles and reactance arcs. Together they locate any impedance.

Tip: Smith chart = R and X.

E9G05

Which of the following is a common use for a Smith chart?

  1. A. Determine the length and position of an impedance matching stub
  2. B. Determine the impedance of a transmission line, given the physical dimensions
  3. C. Determine the gain of an antenna given the physical and electrical parameters
  4. D. Determine the loss/100 feet of a transmission line, given the velocity factor and conductor materials
Show the answer and explanation

Answer: A. Determine the length and position of an impedance matching stub

A common Smith chart job is finding the length and position of a matching stub. You move along the line on the chart until a stub can cancel the reactance.

Tip: Smith chart finds stub length and spot.

E9G06

On the Smith chart shown in Figure E9-3, what is the name for the large outer circle on which the reactance arcs terminate?

Figure E9-3 from the question pool

  1. A. Prime axis
  2. B. Reactance axis
  3. C. Impedance axis
  4. D. Polar axis
Show the answer and explanation

Answer: B. Reactance axis

The large outer circle is where the reactance arcs end. It is called the reactance axis, and it represents zero resistance.

Tip: Outer circle = reactance axis.

E9G07

On the Smith chart shown in Figure E9-3, what is the only straight line shown?

Figure E9-3 from the question pool

  1. A. The reactance axis
  2. B. The current axis
  3. C. The voltage axis
  4. D. The resistance axis
Show the answer and explanation

Answer: D. The resistance axis

The only straight line on a Smith chart is the horizontal resistance axis. It is where reactance is zero.

Tip: Straight line = resistance axis.

E9G08

How is a Smith chart normalized?

  1. A. Reassign the reactance axis with resistance values
  2. B. Reassign the resistance axis with reactance values
  3. C. Reassign the prime center's impedance value
  4. D. Reassign the prime center to the reactance axis
Show the answer and explanation

Answer: C. Reassign the prime center's impedance value

Normalizing a Smith chart means assigning the prime center a chosen impedance, such as 50 ohms. All other values are then scaled to it.

Tip: Normalize: set the center impedance.

E9G09

What third family of circles is often added to a Smith chart during the process of designing impedance matching networks?

  1. A. Constant-SWR circles
  2. B. Transmission line length circles
  3. C. Coaxial-length circles
  4. D. Radiation-pattern circles
Show the answer and explanation

Answer: A. Constant-SWR circles

Constant-SWR circles are drawn around the chart center. Moving along a lossless line keeps you on the same SWR circle.

Tip: Add constant-SWR circles.

E9G10

What do the arcs on a Smith chart represent?

  1. A. Frequency
  2. B. SWR
  3. C. Points with constant resistance
  4. D. Points with constant reactance
Show the answer and explanation

Answer: D. Points with constant reactance

The arcs on a Smith chart connect points that have the same reactance. The circles connect points that have the same resistance.

Tip: Arcs = constant reactance.

E9G11

In what units are the wavelength scales on a Smith chart calibrated?

  1. A. In fractions of transmission line electrical frequency
  2. B. In fractions of transmission line electrical wavelength
  3. C. In fractions of antenna electrical wavelength
  4. D. In fractions of antenna electrical frequency
Show the answer and explanation

Answer: B. In fractions of transmission line electrical wavelength

The scales around the edge of a Smith chart are marked in fractions of a wavelength along the transmission line. One full trip around is a half wavelength.

Tip: Edge scale = fractions of line wavelength.

E9H

Receiving antennas: radio direction finding (RDF) techniques; Beverage antennas; single- and multiple-turn loops

E9H01

When constructing a Beverage antenna, which of the following factors should be included in the design to achieve good performance at the desired frequency?

  1. A. Its overall length must not exceed 1/4 wavelength
  2. B. It must be mounted more than 1 wavelength above ground
  3. C. It should be configured as a four-sided loop
  4. D. It should be at least one wavelength long
Show the answer and explanation

Answer: D. It should be at least one wavelength long

A Beverage is a long, low wire receiving antenna. It needs to be at least one wavelength long to give good directivity.

Tip: Beverage: at least one wavelength long.

E9H02

Which is generally true for 160- and 80-meter receiving antennas?

  1. A. Atmospheric noise is so high that directivity is much more important than losses
  2. B. They must be erected at least 1/2 wavelength above the ground to attain good directivity
  3. C. Low loss coax transmission line is essential for good performance
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. Atmospheric noise is so high that directivity is much more important than losses

On 160 and 80 meters, atmospheric noise is very strong. Directivity to reject noise matters much more than antenna losses for receiving.

Tip: Low bands: directivity beats efficiency.

E9H03

What is receiving directivity factor (RDF)?

  1. A. Forward gain compared to the gain in the reverse direction
  2. B. Relative directivity compared to isotropic
  3. C. Relative directivity compared to a dipole
  4. D. Peak antenna gain compared to average gain over the hemisphere around and above the antenna
Show the answer and explanation

Answer: D. Peak antenna gain compared to average gain over the hemisphere around and above the antenna

RDF compares an antenna's peak gain to its average gain over the hemisphere around and above it. It measures how well the antenna favors signals over noise from all directions.

Tip: RDF = peak gain vs. average gain.

E9H04

What is the purpose of placing an electrostatic shield around a small-loop direction-finding antenna?

  1. A. It adds capacitive loading, increasing the bandwidth of the antenna
  2. B. It eliminates unbalanced capacitive coupling to the antenna's surroundings, improving the depth of its nulls
  3. C. It eliminates tracking errors caused by strong out-of-band signals
  4. D. It increases signal strength by providing a better match to the feed line
Show the answer and explanation

Answer: B. It eliminates unbalanced capacitive coupling to the antenna's surroundings, improving the depth of its nulls

An electrostatic shield removes unbalanced capacitive coupling to nearby objects. That keeps the loop balanced and makes its nulls deeper and sharper.

Tip: Shield the loop for deeper nulls.

E9H05

What challenge is presented by a small wire-loop antenna for direction finding?

  1. A. It has a bidirectional null pattern
  2. B. It does not have a clearly defined null
  3. C. It is practical for use only on VHF and higher bands
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. It has a bidirectional null pattern

A small loop has two nulls, 180 degrees apart. You can find the line to the signal but not which of the two directions it comes from.

Tip: Loop nulls are two-way: ambiguous.

E9H06

What indicates the correct value of terminating resistance for a Beverage antenna?

  1. A. Maximum feed point DC resistance at the center of the desired frequency range
  2. B. Minimum low-angle front-to-back ratio at the design frequency
  3. C. Maximum DC current in the terminating resistor
  4. D. Minimum variation in SWR over the desired frequency range
Show the answer and explanation

Answer: D. Minimum variation in SWR over the desired frequency range

The right terminating resistance makes the Beverage act like a matched line. The SWR then varies the least across the desired frequency range.

Tip: Right termination = flattest SWR.

E9H07

What is the function of a Beverage antenna's termination resistor?

  1. A. Increase the front-to-side ratio
  2. B. Absorb signals from the reverse direction
  3. C. Decrease SWR bandwidth
  4. D. Eliminate harmonic reception
Show the answer and explanation

Answer: B. Absorb signals from the reverse direction

The termination resistor absorbs signals arriving from the back of the Beverage. That makes the antenna unidirectional.

Tip: Resistor soaks up signals from behind.

E9H08

What is the function of a sense antenna?

  1. A. It modifies the pattern of a DF antenna to provide a null in only one direction
  2. B. It increases the sensitivity of a DF antenna array
  3. C. It allows DF antennas to receive signals at different vertical angles
  4. D. It provides diversity reception that cancels multipath signals
Show the answer and explanation

Answer: A. It modifies the pattern of a DF antenna to provide a null in only one direction

A sense antenna adds to a loop or DF antenna's pattern so there is only one null. That removes the 180 degree ambiguity.

Tip: Sense antenna: one null, no ambiguity.

E9H09

What type of radiation pattern is created by a single-turn, terminated loop such as a pennant antenna?

  1. A. Cardioid
  2. B. Bidirectional
  3. C. Omnidirectional
  4. D. Hyperbolic
Show the answer and explanation

Answer: A. Cardioid

A terminated single-turn loop like the pennant has a cardioid pattern. The resistor makes it favor one direction with a null to the rear.

Tip: Pennant = cardioid.

E9H10

How can the output voltage of a multiple-turn receiving loop antenna be increased?

  1. A. By reducing the permeability of the loop shield
  2. B. By utilizing high impedance wire for the coupling loop
  3. C. By increasing the number of turns and/or the area enclosed by the loop
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. By increasing the number of turns and/or the area enclosed by the loop

Loop output voltage rises with the number of turns and the area of the loop. More turns or a bigger loop captures more signal.

Tip: More turns, more area, more voltage.

E9H11

What feature of a cardioid pattern antenna makes it useful for direction-finding antennas?

  1. A. A very sharp peak
  2. B. A single null
  3. C. Broadband response
  4. D. High radiation angle
Show the answer and explanation

Answer: B. A single null

A cardioid pattern has a single, deep null. Pointing that null at a signal shows its direction without ambiguity.

Tip: Cardioid: one null for DF.

Practice E9 with scoring Take a 50-question practice exam