Ham Tech Prep

Technician › T6

T6 Electronic and Electrical Components

46 questions in the pool. Your exam will include 4, one from each group below.

Practice T6 now

T6A

Fixed and variable resistors; Capacitors; Inductors; Fuses; Switches; Batteries

T6A01

What electrical component opposes the flow of current in a DC circuit?

  1. A. Inductor
  2. B. Resistor
  3. C. Inverter
  4. D. Transformer
Show the answer and explanation

Answer: B. Resistor

A resistor's whole job is to oppose, or resist, the flow of current. In a DC circuit, that opposition is called resistance and is measured in ohms. Inductors mainly oppose changes in current, not steady DC.

Tip: Resistor = resists current.

T6A02

What type of component is often used as an adjustable volume control?

  1. A. Fixed resistor
  2. B. Power resistor
  3. C. Potentiometer
  4. D. Transformer
Show the answer and explanation

Answer: C. Potentiometer

A potentiometer is a resistor with a sliding contact you can move by turning a knob. Turning it changes how much signal gets through, which makes it a classic volume control. A fixed resistor cannot be adjusted.

Tip: Turn the knob, change the pot: the classic volume control.

T6A03

What electrical parameter is controlled by a potentiometer?

  1. A. Inductance
  2. B. Resistance
  3. C. Capacitance
  4. D. Field strength
Show the answer and explanation

Answer: B. Resistance

A potentiometer is a variable resistor, so it controls resistance. Moving its wiper changes how much resistive material is in the path between its terminals.

Tip: Pot = adjustable resistance.

T6A04

What electrical component stores energy in an electric field?

  1. A. Resistor
  2. B. Capacitor
  3. C. Inductor
  4. D. Diode
Show the answer and explanation

Answer: B. Capacitor

A capacitor stores energy in an electric field between its plates. When it is charged, opposite charges build up on the two plates, and the field between them holds the energy. An inductor stores energy in a magnetic field instead.

Tip: Capacitor = electric field; inductor = magnetic field.

T6A05

What type of electrical component consists of conductive surfaces separated by an insulator?

  1. A. Resistor
  2. B. Potentiometer
  3. C. Oscillator
  4. D. Capacitor
Show the answer and explanation

Answer: D. Capacitor

A capacitor is built from two conductive surfaces, called plates, with an insulator (the dielectric) between them. The insulator keeps the plates from touching so charge can build up on each side.

Tip: Two plates plus an insulator in between makes a capacitor.

T6A06

What type of electrical component stores energy in a magnetic field?

  1. A. Resistor
  2. B. Capacitor
  3. C. Inductor
  4. D. Diode
Show the answer and explanation

Answer: C. Inductor

An inductor stores energy in a magnetic field. Current flowing through its coil creates a magnetic field around it, and that field holds the energy. A capacitor uses an electric field instead.

Tip: Inductor = coil = magnetic field.

T6A07

What electrical component is typically constructed as a coil of wire?

  1. A. Transistor
  2. B. Capacitor
  3. C. Diode
  4. D. Inductor
Show the answer and explanation

Answer: D. Inductor

An inductor is usually a coil of wire, sometimes wound around a core. Coiling the wire concentrates the magnetic field and increases the inductance.

Tip: Coil of wire? Think inductor.

T6A08

What is the function of an SPDT switch?

  1. A. A single circuit is opened or closed
  2. B. Two circuits are opened or closed
  3. C. A single circuit is switched between one of two other circuits
  4. D. Two circuits are each switched between one of two other circuits
Show the answer and explanation

Answer: C. A single circuit is switched between one of two other circuits

SPDT means single-pole, double-throw. Single pole means one circuit is being switched, and double throw means it can connect to either of two positions. So a single circuit is switched between one of two other circuits.

Tip: Pole = how many circuits; throw = how many positions each can go to.

T6A09

What type of switch is represented by component 3 in figure T-2?

Figure T-2 from the question pool

  1. A. Single-pole single-throw
  2. B. Single-pole double-throw
  3. C. Double-pole single-throw
  4. D. Double-pole double-throw
Show the answer and explanation

Answer: A. Single-pole single-throw

Component 3 in Figure T-2 is a simple switch: one moving arm with one contact it can close against. One pole and one possible connection make it single-pole single-throw (SPST), a basic on/off switch.

Tip: One arm, one contact: SPST, a plain on/off switch.

T6A10

Which of the following battery chemistries is rechargeable?

  1. A. Nickel-metal hydride
  2. B. Lithium-ion
  3. C. Lead-acid
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Nickel-metal hydride, lithium-ion, and lead-acid batteries can all be recharged. NiMH is common in AA-size rechargeables, lithium-ion is in phones and handheld radios, and lead-acid is used in car batteries. So all these choices are correct.

Tip: NiMH, Li-ion, and lead-acid all recharge.

T6A11

Which of the following battery chemistries is not rechargeable?

  1. A. Nickel-cadmium
  2. B. Carbon-zinc
  3. C. Lead-acid
  4. D. Lithium-ion
Show the answer and explanation

Answer: B. Carbon-zinc

Carbon-zinc batteries are basic primary cells that are meant to be used once and thrown away. Nickel-cadmium, lead-acid, and lithium-ion are all rechargeable types.

Tip: Carbon-zinc is the cheap one-and-done battery.

T6B

Semiconductors: basic principles and applications of solid-state devices, diodes and transistors; Gain

T6B01

Which is true about forward voltage drop in a diode?

  1. A. It is lower in some diode types than in others
  2. B. It is proportional to peak inverse voltage
  3. C. It indicates that the diode is defective
  4. D. It has no impact on the voltage delivered to the load
Show the answer and explanation

Answer: A. It is lower in some diode types than in others

Forward voltage drop is the small voltage lost across a diode when current flows through it. It is a normal property of every diode, and its size depends on the type: for example, a Schottky diode usually drops less than a regular silicon diode. A drop does not mean the diode is bad.

Tip: Every diode drops some voltage; some types drop less.

T6B02

What electronic component allows current to flow in only one direction?

  1. A. Resistor
  2. B. Fuse
  3. C. Diode
  4. D. Driven element
Show the answer and explanation

Answer: C. Diode

A diode acts like a one-way valve for electricity. It lets current flow in one direction and blocks it in the other. A fuse lets current flow either way until it blows.

Tip: Diode = one-way street for current.

T6B03

Which of these components can be used as an electronic switch?

  1. A. Varistor
  2. B. Potentiometer
  3. C. Transistor
  4. D. Thermistor
Show the answer and explanation

Answer: C. Transistor

A transistor can be used as an electronic switch. A small current or voltage at its control lead can turn a much larger current on or off. Varistors, potentiometers, and thermistors are kinds of resistors and are not used as switches this way.

Tip: Transistors switch and amplify.

T6B04

Which of the following components can consist of three regions of semiconductor material?

  1. A. Alternator
  2. B. Transistor
  3. C. Triode
  4. D. Pentode
Show the answer and explanation

Answer: B. Transistor

A bipolar transistor is made from three layers, or regions, of semiconductor material, such as NPN or PNP. Triodes and pentodes are vacuum tubes, not semiconductor parts.

Tip: NPN or PNP: three layers make a transistor.

T6B05

What type of transistor has a gate, drain, and source?

  1. A. Varistor
  2. B. Field-effect
  3. C. Hall-effect
  4. D. Bipolar junction
Show the answer and explanation

Answer: B. Field-effect

A field-effect transistor (FET) has three leads called the gate, drain, and source. A bipolar junction transistor instead uses emitter, base, and collector.

Tip: FET: gate, drain, source. BJT: emitter, base, collector.

T6B06

How is the cathode lead of a semiconductor diode often marked on the package?

  1. A. With the word "cathode"
  2. B. With a stripe
  3. C. With the letter C
  4. D. With the letter K
Show the answer and explanation

Answer: B. With a stripe

The cathode end of a diode is usually marked with a stripe or band around the body. The stripe matches the bar in the diode's schematic symbol, which is also the cathode side.

Tip: Stripe on the part, bar on the symbol: both mean cathode.

T6B07

What causes a light-emitting diode (LED) to emit light?

  1. A. Forward current
  2. B. Reverse current
  3. C. Capacitively-coupled RF signal
  4. D. Inductively-coupled RF signal
Show the answer and explanation

Answer: A. Forward current

An LED gives off light when current flows through it in the forward direction. With reverse voltage, almost no current flows and the LED stays dark.

Tip: Forward current makes an LED glow.

T6B08

What does the abbreviation FET stand for?

  1. A. Frequency Emission Transmitter
  2. B. Fast Electron Transistor
  3. C. Free Electron Transmitter
  4. D. Field Effect Transistor
Show the answer and explanation

Answer: D. Field Effect Transistor

FET stands for Field Effect Transistor. It gets its name because an electric field from the gate voltage controls the current flowing between source and drain.

Tip: FET = Field Effect Transistor.

T6B09

What are the names for the electrodes of a diode?

  1. A. Plus and minus
  2. B. Source and drain
  3. C. Anode and cathode
  4. D. Gate and base
Show the answer and explanation

Answer: C. Anode and cathode

The two leads of a diode are the anode and the cathode. Conventional current flows into the anode and out of the cathode when the diode conducts. Source and drain belong to a FET, not a diode.

Tip: Diode leads: anode in, cathode out.

T6B10

Which of the following can provide power gain?

  1. A. Transformer
  2. B. Transistor
  3. C. Reactor
  4. D. Resistor
Show the answer and explanation

Answer: B. Transistor

A transistor can provide power gain: a small input signal controls a larger output signal, with the extra power coming from the power supply. A transformer can raise voltage, but it cannot put out more power than it takes in.

Tip: Transistors amplify; transformers only trade voltage for current.

T6B11

What does the term gain mean in amplifiers?

  1. A. The output signal voltage relative to the input signal voltage
  2. B. The output signal current relative to the input signal current
  3. C. The output signal power relative to the input signal power
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Gain compares an amplifier's output to its input. That comparison can be made for voltage, current, or power, so all these choices are correct.

Tip: Gain = output compared to input, for voltage, current, or power.

T6B12

What are the names of the electrodes of a bipolar junction transistor?

  1. A. Signal, bias, power
  2. B. Emitter, base, collector
  3. C. Input, output, supply
  4. D. Pole one, pole two, output
Show the answer and explanation

Answer: B. Emitter, base, collector

The three leads of a bipolar junction transistor are the emitter, base, and collector. The base controls how much current flows between the collector and emitter.

Tip: BJT: Emitter, Base, Collector.

T6C

Circuit diagrams: use of term schematic, basic structure; Schematic symbols of basic components

T6C01

What is an electrical diagram using standard component symbols called?

  1. A. Connection chart
  2. B. Instrumentation system
  3. C. Schematic
  4. D. Flow chart
Show the answer and explanation

Answer: C. Schematic

A schematic is a drawing of a circuit that uses standard symbols for each part. It shows how the parts connect, not what they look like. A flow chart shows steps in a process, not electrical parts.

Tip: Symbols plus connecting lines make a schematic.

T6C02

What is component 1 in figure T-1?

Figure T-1 from the question pool

  1. A. Resistor
  2. B. Transistor
  3. C. Battery
  4. D. Connector
Show the answer and explanation

Answer: A. Resistor

Component 1 in Figure T-1 is a zigzag line, which is the standard symbol for a resistor. It sits between the input connector and the transistor.

Tip: Zigzag line = resistor.

T6C03

What is component 2 in figure T-1?

Figure T-1 from the question pool

  1. A. Resistor
  2. B. Transistor
  3. C. Indicator lamp
  4. D. Connector
Show the answer and explanation

Answer: B. Transistor

Component 2 in Figure T-1 is a circle with a thick bar inside and two slanted lines, one with an arrow. That is the symbol for a bipolar transistor; the arrow marks the emitter.

Tip: Circle with a bar and an arrowed lead = transistor.

T6C04

What is component 3 in figure T-1?

Figure T-1 from the question pool

  1. A. Resistor
  2. B. Transistor
  3. C. Lamp
  4. D. Ground symbol
Show the answer and explanation

Answer: C. Lamp

Component 3 in Figure T-1 looks like a small rounded dome with a loop inside, sitting on top of the circuit line. That is the symbol for a lamp, such as an indicator bulb, here switched by the transistor.

Tip: Rounded bulb shape = lamp.

T6C05

What is component 4 in figure T-1?

Figure T-1 from the question pool

  1. A. Resistor
  2. B. Transistor
  3. C. Ground symbol
  4. D. Battery
Show the answer and explanation

Answer: D. Battery

Component 4 in Figure T-1 is a stack of parallel lines that alternate long and short. That is the symbol for a battery; each long and short pair stands for one cell.

Tip: Long-short line pairs = battery.

T6C06

What is component 6 in figure T-2?

Figure T-2 from the question pool

  1. A. Resistor
  2. B. Capacitor
  3. C. Regulator IC
  4. D. Transistor
Show the answer and explanation

Answer: B. Capacitor

Component 6 in Figure T-2 has one straight line and one curved line facing each other with a gap between them. That is the symbol for a capacitor, here used to smooth the output of the diode.

Tip: Two plates with a gap = capacitor.

T6C07

What is component 8 in figure T-2?

Figure T-2 from the question pool

  1. A. Resistor
  2. B. Inductor
  3. C. Regulator IC
  4. D. Light emitting diode
Show the answer and explanation

Answer: D. Light emitting diode

Component 8 in Figure T-2 is a diode symbol (a triangle pointing at a bar) with two small arrows pointing away from it. The outward arrows show light leaving the part, so it is a light emitting diode.

Tip: Diode with arrows pointing out = LED.

T6C08

What is component 9 in figure T-2?

Figure T-2 from the question pool

  1. A. Variable capacitor
  2. B. Variable inductor
  3. C. Variable resistor
  4. D. Variable transformer
Show the answer and explanation

Answer: C. Variable resistor

Component 9 in Figure T-2 is a zigzag resistor symbol with an arrow touching it. The arrow means the value can be changed, so it is a variable resistor.

Tip: Arrow on a zigzag = variable resistor.

T6C09

What is component 4 in figure T-2?

Figure T-2 from the question pool

  1. A. Variable inductor
  2. B. Double-pole switch
  3. C. Potentiometer
  4. D. Transformer
Show the answer and explanation

Answer: D. Transformer

Component 4 in Figure T-2 shows two coils side by side with straight lines between them. Two coils sharing a core is the symbol for a transformer; here it steps down the AC power before the diode.

Tip: Two coils with lines between = transformer.

T6C10

What is component 3 in figure T-3?

Figure T-3 from the question pool

  1. A. Connector
  2. B. Meter
  3. C. Variable capacitor
  4. D. Variable inductor
Show the answer and explanation

Answer: D. Variable inductor

Component 3 in Figure T-3 is a coil (a row of loops) with an arrow tapping into it. A coil is an inductor, and the arrow shows its value can be adjusted, so it is a variable inductor.

Tip: Coil plus arrow = variable inductor.

T6C11

What is component 4 in figure T-3?

Figure T-3 from the question pool

  1. A. Antenna
  2. B. Transmitter
  3. C. Dummy load
  4. D. Ground
Show the answer and explanation

Answer: A. Antenna

Component 4 in Figure T-3 is a line going up into a downward-pointing triangle with a line through it. That is the symbol for an antenna, at the output end of the tuning circuit.

Tip: A 'T' inside a triangle on a pole = antenna.

T6C12

Which of the following is accurately represented in electrical schematics?

  1. A. Wire lengths
  2. B. Physical appearance of components
  3. C. Component connections
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. Component connections

A schematic accurately shows how components are connected to each other. It does not show real wire lengths or what the parts physically look like.

Tip: Schematics show connections, not looks or lengths.

T6D

Component functions: rectifiers, relays, voltage regulators, meters, indicators, integrated circuits, transformers; Resonant circuit; Shielding

T6D01

Which of the following devices or circuits changes an alternating current into a varying direct current signal?

  1. A. Transformer
  2. B. Rectifier
  3. C. Amplifier
  4. D. Reflector
Show the answer and explanation

Answer: B. Rectifier

A rectifier changes alternating current (AC) into direct current (DC) that still varies, or pulses. It is usually built from diodes that let current pass in only one direction. A transformer changes AC voltage but leaves it as AC.

Tip: Rectifier: AC in, pulsing DC out.

T6D02

What is a relay?

  1. A. An electrically-controlled switch
  2. B. A current-controlled amplifier
  3. C. An inverting amplifier
  4. D. A pass transistor
Show the answer and explanation

Answer: A. An electrically-controlled switch

A relay is a switch that is operated by electricity. A small current through its coil makes a magnet pull the switch contacts open or closed.

Tip: Relay = electrically controlled switch.

T6D03

Which of the following is a reason to use shielded wire?

  1. A. To decrease the resistance of DC power connections
  2. B. To increase the current carrying capability of the wire
  3. C. To prevent coupling of unwanted signals to or from the wire
  4. D. To reduce receiver overload
Show the answer and explanation

Answer: C. To prevent coupling of unwanted signals to or from the wire

Shielded wire has a metal braid or foil around the inner wire. The shield keeps unwanted signals from getting into the wire and keeps signals in the wire from leaking out. It does not lower DC resistance or raise current capacity.

Tip: Shield keeps signals from getting in or leaking out.

T6D04

Which of the following displays an electrical quantity as a numeric value?

  1. A. Potentiometer
  2. B. Transistor
  3. C. Meter
  4. D. Relay
Show the answer and explanation

Answer: C. Meter

A meter shows an electrical quantity, like voltage or current, as a number. A potentiometer adjusts resistance, and a relay is a switch; neither displays a value.

Tip: Meters measure and display.

T6D05

What type of circuit controls the amount of voltage from a power supply?

  1. A. Regulator
  2. B. Oscillator
  3. C. Filter
  4. D. Phase inverter
Show the answer and explanation

Answer: A. Regulator

A regulator circuit controls the output voltage of a power supply and holds it steady even when the load or input changes. An oscillator makes a signal, and a filter smooths or blocks signals.

Tip: Regulator keeps voltage regular.

T6D06

What component changes 120 V AC power to a lower AC voltage for other uses?

  1. A. Variable capacitor
  2. B. Transformer
  3. C. Transistor
  4. D. Diode
Show the answer and explanation

Answer: B. Transformer

A transformer changes AC voltage up or down using two coils on a shared core. A step-down transformer turns 120 V AC from the wall into a lower AC voltage.

Tip: Transformers change AC voltage.

T6D07

Which of the following is commonly used as a visual indicator?

  1. A. LED
  2. B. FET
  3. C. Zener diode
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. LED

An LED is commonly used as a visual indicator because it glows when current flows, like a power-on light. A FET and a Zener diode do not give off light.

Tip: LED = the little light that says 'on'.

T6D08

Which of the following is combined with an inductor to make a resonant circuit?

  1. A. Resistor
  2. B. Zener diode
  3. C. Potentiometer
  4. D. Capacitor
Show the answer and explanation

Answer: D. Capacitor

An inductor and a capacitor together form a resonant, or tuned, circuit. At one frequency their reactances are equal, and the circuit resonates there. This LC combination is used to tune radios.

Tip: L plus C makes it resonate.

T6D09

What is the name of a device that combines several semiconductors and other components into one package?

  1. A. Transducer
  2. B. Multi-pole relay
  3. C. Integrated circuit
  4. D. Transformer
Show the answer and explanation

Answer: C. Integrated circuit

An integrated circuit, or IC, puts many transistors and other components together on one chip in a single package. A transducer converts one kind of energy into another, which is different.

Tip: IC = many parts integrated into one chip.

T6D10

What is the function of component 2 in figure T-1?

Figure T-1 from the question pool

  1. A. Give off light when current flows through it
  2. B. Supply electrical energy
  3. C. Control the flow of current
  4. D. Convert electrical energy into radio waves
Show the answer and explanation

Answer: C. Control the flow of current

Component 2 in Figure T-1 is a transistor. In this circuit, a small signal at its base controls the larger current through the lamp, so its job is to control the flow of current. The lamp gives off light and the battery supplies energy.

Tip: The transistor is the circuit's controller.

T6D11

Which of the following is a resonant or tuned circuit?

  1. A. An inductor and a capacitor in series or parallel
  2. B. A linear voltage regulator
  3. C. A resistor circuit used for reducing standing wave ratio
  4. D. A circuit designed to provide high-fidelity audio
Show the answer and explanation

Answer: A. An inductor and a capacitor in series or parallel

A resonant or tuned circuit is made from an inductor and a capacitor, connected either in series or in parallel. It responds strongly at one frequency, called the resonant frequency. A voltage regulator or a resistor circuit is not tuned.

Tip: LC in series or parallel = tuned circuit.

Practice T6 with scoring Take a 35-question practice exam