Ham Tech Prep

Technician › T4

T4 Amateur Radio Practices

23 questions in the pool. Your exam will include 2, one from each group below.

Practice T4 now

T4A

Station setup: connecting a microphone, RF power meter, a power source, a computer, digital equipment, an SWR meter; RF grounding; Mobile radio installation

T4A01

Which of the following is an appropriate power supply rating for a typical 50-watt output mobile FM transceiver?

  1. A. 24.0 volts at 4 amperes
  2. B. 13.8 volts at 4 amperes
  3. C. 24.0 volts at 12 amperes
  4. D. 13.8 volts at 12 amperes
Show the answer and explanation

Answer: D. 13.8 volts at 12 amperes

Mobile radios are built to run from a car's electrical system, which is about 13.8 volts while the engine is running, so the answer is 13.8 volts at 12 amperes. A 50-watt transmitter is not 100% efficient, so it draws much more than 50 watts of input power. 13.8 V x 4 A is only about 55 W, which leaves no headroom, while 13.8 V x 12 A is about 166 W, which is plenty.

Tip: Mobile rigs: 13.8 V. Pick a supply with current to spare.

T4A02

Which of the following should be considered when selecting an accessory SWR meter?

  1. A. The frequency and power level at which the measurements will be made
  2. B. The distance that the meter will be located from the antenna
  3. C. The maximum SWR anticipated on the transmission line
  4. D. The ability of the meter to compensate for a poor transmission line match to the antenna
Show the answer and explanation

Answer: A. The frequency and power level at which the measurements will be made

An SWR meter is designed to work over a certain range of frequencies and power levels. So you should consider the frequency and power level at which the measurements will be made. A meter built for HF may read poorly at UHF, and too much power can damage it.

Tip: Match the meter to your band and your power.

T4A03

Why are short, heavy-gauge wires used for a transceiver's DC power connection?

  1. A. To minimize voltage drop when transmitting
  2. B. To provide a close match to the power supply output impedance
  3. C. To avoid RF interference
  4. D. To minimize radiative losses in the power cable
Show the answer and explanation

Answer: A. To minimize voltage drop when transmitting

A transmitting radio draws a lot of current, and thin or long wires have more resistance. That resistance causes voltage drop, so the radio gets less voltage than the supply provides. Short, heavy-gauge wires are used to minimize voltage drop when transmitting.

Tip: Thick and short = low resistance = little voltage drop.

T4A04

How are the audio input and output of a transceiver connected in a station configured to operate using FT8?

  1. A. To a computer running a terminal program and connected to a terminal node controller unit
  2. B. To the audio output and input of a computer running FT8 software
  3. C. To an FT8 conversion unit, a keyboard, and a computer monitor
  4. D. To a computer connected to the FT8converter.com website
Show the answer and explanation

Answer: B. To the audio output and input of a computer running FT8 software

FT8 is a digital mode that a computer turns into audio tones. The radio's audio output and input connect to the audio output and input of a computer running FT8 software. The computer listens to received tones and sends tones back to the radio to transmit. No special converter box or website is needed.

Tip: FT8 = radio audio <-> computer sound card + FT8 software.

T4A05

Where should an RF power meter be installed?

  1. A. In the feed line, between the transmitter and antenna
  2. B. At the power supply output
  3. C. In parallel with the push-to-talk line and the antenna
  4. D. In the power supply cable, as close as possible to the radio
Show the answer and explanation

Answer: A. In the feed line, between the transmitter and antenna

An RF power meter measures the radio energy going to the antenna. That energy travels in the feed line, so the meter goes in the feed line, between the transmitter and antenna. The power supply cable only carries DC, not RF.

Tip: RF meter goes where the RF flows: the feed line.

T4A06

What signals are used in a computer-radio interface for digital mode operation?

  1. A. Receive and transmit mode, status, and location
  2. B. Antenna and RF power
  3. C. Receive audio, transmit audio, and transmitter keying
  4. D. NMEA GPS location and DC power
Show the answer and explanation

Answer: C. Receive audio, transmit audio, and transmitter keying

For digital modes, the computer needs to hear the radio, talk to the radio, and switch it to transmit. Those three signals are receive audio, transmit audio, and transmitter keying (push-to-talk).

Tip: Hear, talk, key: RX audio, TX audio, PTT.

T4A07

Which of the following is one of the connections required between a computer and a transceiver to operate digital modes?

  1. A. Computer “line out” to transceiver push-to-talk
  2. B. Computer “line in” to transceiver push-to-talk
  3. C. Computer “line in” to transceiver speaker connector
  4. D. Computer “line out” to transceiver speaker connector
Show the answer and explanation

Answer: C. Computer “line in” to transceiver speaker connector

The computer must hear what the radio receives. Received audio comes out of the transceiver's speaker connector and goes into the computer's "line in". So computer "line in" to transceiver speaker connector is correct. Audio does not key push-to-talk.

Tip: Speaker out feeds computer line in.

T4A08

Which of the following conductors is preferred for bonding at RF?

  1. A. Copper braid removed from coaxial cable
  2. B. Copper-clad steel wire
  3. C. Twisted-pair cable
  4. D. Flat copper strap
Show the answer and explanation

Answer: D. Flat copper strap

At radio frequencies, current travels mostly on the surface of a conductor (skin effect). A flat copper strap has lots of surface area and low inductance, so it is the preferred choice for RF bonding. Round wire or braid has less surface and more inductance.

Tip: RF bonding: flat copper strap, wide and short.

T4A09

How can you determine the length of time that equipment can be powered from a battery?

  1. A. Divide the watt-hour rating of the battery by the peak power consumption of the equipment
  2. B. Divide the battery ampere-hour rating by the average current draw of the equipment
  3. C. Multiply the watts per hour consumed by the equipment by the battery power rating
  4. D. Multiply the square of the current rating of the battery by the input resistance of the equipment
Show the answer and explanation

Answer: B. Divide the battery ampere-hour rating by the average current draw of the equipment

A battery's ampere-hour rating tells how much current it can supply over time. Divide the battery ampere-hour rating by the average current draw of the equipment to get the hours of run time. For example, a 20 Ah battery with a 2 A average draw lasts about 20 / 2 = 10 hours. Use average current, not peak, because the radio is not transmitting all the time.

Tip: Hours = amp-hours / average amps.

T4A10

What function does a digital mode hotspot perform for nearby transceivers?

  1. A. Communication with a digital voice or data network
  2. B. FT8 digital communications via AFSK using a smartphone connected to the internet
  3. C. RTTY encoding and decoding without a computer
  4. D. High-speed digital communications for meteor scatter
Show the answer and explanation

Answer: A. Communication with a digital voice or data network

A hotspot is a small, low-power device that links your digital radio to the internet. It provides communication with a digital voice or data network, such as DMR or D-STAR networks. Your handheld talks to the hotspot by radio, and the hotspot passes your signal over the internet.

Tip: Hotspot = your personal gateway to a digital network.

T4A11

Where should the negative power return of a mobile transceiver be connected in a vehicle?

  1. A. At the 12-volt battery chassis ground
  2. B. To the shell of the power connector
  3. C. To any metal part of the vehicle
  4. D. Through the transceiver's mounting bracket
Show the answer and explanation

Answer: A. At the 12-volt battery chassis ground

The negative lead of a mobile radio should go to the 12-volt battery chassis ground connection. This gives a solid, low-resistance return path. Connecting to random metal parts or the mounting bracket can give poor connections and noise.

Tip: Negative lead goes back to the battery's ground point.

T4A12

What is an electronic keyer?

  1. A. A device for switching antennas from transmit to receive
  2. B. A device for voice activated switching from receive to transmit
  3. C. A device that assists in manual sending of Morse code
  4. D. An interlock to prevent unauthorized use of a radio
Show the answer and explanation

Answer: C. A device that assists in manual sending of Morse code

An electronic keyer is a device that assists in manual sending of Morse code. You use a paddle, and the keyer automatically makes evenly timed dots and dashes. This makes your code cleaner and easier to copy.

Tip: Keyer = automatic, evenly spaced dits and dahs.

T4B

Operating controls: frequency tuning, use of filters, squelch function, AGC, memory channels, noise blanker, microphone gain, receiver incremental tuning (RIT), bandwidth selection, scanning function; Digital transceiver configuration; DMR code plugs and talk groups

T4B01

What is the effect of excessive microphone gain on SSB transmissions?

  1. A. Frequency instability
  2. B. Distorted transmitted audio
  3. C. Increased SWR
  4. D. Sideband inversion
Show the answer and explanation

Answer: B. Distorted transmitted audio

If the microphone gain is too high on SSB, the audio overdrives the transmitter. The result is distorted transmitted audio that is hard to understand and can splatter onto nearby frequencies. It does not change the SWR or the frequency.

Tip: Too much mic gain = distortion and splatter.

T4B02

Which of the following can be used to enter a transceiver's operating frequency?

  1. A. The keypad or VFO knob
  2. B. The CTCSS or DTMF encoder
  3. C. The Automatic Frequency Control
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. The keypad or VFO knob

You can set a radio's operating frequency with the keypad or VFO knob. The keypad lets you type the frequency, and the VFO (variable frequency oscillator) knob lets you tune up and down. CTCSS and DTMF are tone systems, not frequency entry methods.

Tip: Type it or turn it: keypad or VFO knob.

T4B03

How is squelch adjusted so that a weak FM signal can be heard?

  1. A. Set the squelch threshold so that receiver output audio is on all the time
  2. B. Turn up the audio level until it overcomes the squelch threshold
  3. C. Turn on the anti-squelch function
  4. D. Enable squelch enhancement
Show the answer and explanation

Answer: A. Set the squelch threshold so that receiver output audio is on all the time

Squelch silences the receiver when no signal is strong enough to open it. A weak signal may not open the squelch. To hear it, set the squelch threshold so that receiver output audio is on all the time (squelch fully open). Turning up the volume does not help because the squelch is still blocking the audio.

Tip: Weak signal? Open the squelch all the way.

T4B04

What does an FM signal sound like when received slightly off frequency?

  1. A. The audio increases in pitch
  2. B. The audio decrease in pitch
  3. C. There is no effect except for reduction in amplitude
  4. D. The audio becomes distorted
Show the answer and explanation

Answer: D. The audio becomes distorted

An FM receiver decodes changes in frequency. If you are tuned slightly off frequency, the signal falls partly outside the receiver's passband and the audio becomes distorted. The pitch does not change the way it does with SSB.

Tip: FM off frequency = distorted, not pitch-shifted.

T4B05

What does the scanning function of an FM transceiver do?

  1. A. Checks incoming signal deviation
  2. B. Prevents interference to nearby repeaters
  3. C. Tunes through a range of frequencies to check for activity
  4. D. Tunes through a range of frequencies to determine the antenna's resonant frequency
Show the answer and explanation

Answer: C. Tunes through a range of frequencies to check for activity

The scan function tunes through a range of frequencies to check for activity. It stops when it finds a signal so you can listen. It is a way to find who is on the air without tuning by hand.

Tip: Scan = search for activity.

T4B06

Which of the following controls could be used if the voice pitch of a single-sideband signal returning to your CQ call seems too high or low?

  1. A. The AGC or limiter
  2. B. The bandwidth selection
  3. C. The tone squelch
  4. D. The RIT or Clarifier
Show the answer and explanation

Answer: D. The RIT or Clarifier

With SSB, if your receive frequency is a little off, the voice sounds too high or too low in pitch. The RIT (Receiver Incremental Tuning) or Clarifier fine-tunes only your receiver without moving your transmit frequency. That fixes the pitch of the other station's voice.

Tip: SSB voice sounds funny? Adjust RIT / Clarifier.

T4B07

What is a DMR “code plug”?

  1. A. An adapter cable used to connect a DMR radio to a computer for internet access
  2. B. Configuration data loaded onto your radio to access repeaters and talkgroups
  3. C. An upgrade to DMR programming software provided by the radio manufacturer to accommodate new radio models
  4. D. A Coder-Decoder (CODEC) that converts analog voice data to DMR digital data and vice versa
Show the answer and explanation

Answer: B. Configuration data loaded onto your radio to access repeaters and talkgroups

A DMR code plug is configuration data loaded onto your radio to access repeaters and talkgroups. It holds frequencies, color codes, talkgroups, and your ID. It is a file, not a physical plug or cable.

Tip: Code plug = the radio's settings file.

T4B08

What is the advantage of having a choice of receiver filter bandwidths in a multimode transceiver?

  1. A. Permits monitoring several modes simultaneously by selecting a separate filter for each mode
  2. B. Permits noise or interference reduction by selecting a bandwidth matching the mode
  3. C. Increases the number of frequencies that can be stored in memory
  4. D. Increases the amount of offset between receive and transmit frequencies
Show the answer and explanation

Answer: B. Permits noise or interference reduction by selecting a bandwidth matching the mode

Different modes need different bandwidths, such as narrow for CW and wider for SSB. Choosing a filter bandwidth matching the mode permits noise or interference reduction. A filter wider than needed lets in extra noise and nearby signals.

Tip: Filter as narrow as the mode allows.

T4B09

How is a specific group of stations selected on a DMR digital voice transceiver?

  1. A. By retrieving the frequencies from transceiver memory
  2. B. By enabling the group's CTCSS tone
  3. C. By entering the group's identification code
  4. D. By inserting a five-pin, pre-programmed code plug
Show the answer and explanation

Answer: C. By entering the group's identification code

On DMR, groups of stations are organized into talkgroups. You select a group by entering the group's identification code (the talkgroup ID). CTCSS tones are used on analog FM, not for choosing DMR talkgroups.

Tip: DMR talkgroup = pick it by ID number.

T4B10

Which of the following receiver filter bandwidths provides the best signal-to-noise ratio for SSB reception?

  1. A. 500 Hz
  2. B. 1000 Hz
  3. C. 2400 Hz
  4. D. 5000 Hz
Show the answer and explanation

Answer: C. 2400 Hz

An SSB voice signal is about 2.4 to 3 kHz wide. A 2400 Hz filter passes the voice while blocking extra noise, giving the best signal-to-noise ratio. 500 Hz and 1000 Hz are too narrow for voice (they suit CW), and 5000 Hz lets in more noise.

Tip: SSB = 2400 Hz, CW = 500 Hz.

T4B11

Which of the following must be programmed into a D-STAR digital transceiver before transmitting?

  1. A. Your call sign
  2. B. Your output power
  3. C. The codec type being used
  4. D. All these choices are correct
Show the answer and explanation

Answer: A. Your call sign

D-STAR sends your call sign as part of the digital data in every transmission. So your call sign must be programmed into a D-STAR digital transceiver before transmitting. Output power and codec are not things you must enter.

Tip: D-STAR: program your call sign first.

Practice T4 with scoring Take a 35-question practice exam