Ham Tech Prep

General › G8

G8 Signals and Emissions

42 questions in the pool. Your exam will include 3, one from each group below.

Practice G8 now

G8A

Carriers and modulation: AM, FM, and single sideband; modulation envelope; digital modulation; overmodulation; link budgets and link margins

G8A01

How is direct binary FSK modulation generated?

  1. A. By keying an FM transmitter with a sub-audible tone
  2. B. By changing an oscillator's frequency directly with a digital control signal
  3. C. By using a transceiver's computer data interface protocol to change frequencies
  4. D. By reconfiguring the CW keying input to act as a tone generator
Show the answer and explanation

Answer: B. By changing an oscillator's frequency directly with a digital control signal

Direct FSK shifts the oscillator's frequency itself between two values under control of the digital data signal. No audio tones are involved, unlike AFSK.

Tip: Direct FSK: data directly shifts the oscillator.

G8A02

What is the name of the process that changes the phase angle of an RF signal to convey information?

  1. A. Phase convolution
  2. B. Phase modulation
  3. C. Phase transformation
  4. D. Phase inversion
Show the answer and explanation

Answer: B. Phase modulation

Varying the phase angle of an RF signal to carry information is phase modulation. The other names are made-up terms.

Tip: Phase changes = phase modulation.

G8A03

What is the name of the process that changes the instantaneous frequency of an RF wave to convey information?

  1. A. Frequency convolution
  2. B. Frequency transformation
  3. C. Frequency conversion
  4. D. Frequency modulation
Show the answer and explanation

Answer: D. Frequency modulation

Changing the instantaneous frequency of an RF wave to carry information is frequency modulation (FM). Frequency conversion is mixing to a new frequency, not modulation.

Tip: Frequency changes = FM.

G8A04

What emission is produced by a reactance modulator connected to a transmitter RF amplifier stage?

  1. A. Multiplex modulation
  2. B. Phase modulation
  3. C. Amplitude modulation
  4. D. Pulse modulation
Show the answer and explanation

Answer: B. Phase modulation

A reactance modulator varies the reactance in an amplifier stage, which shifts the phase of the RF signal, producing phase modulation. This is a common way to make FM-like signals.

Tip: Reactance modulator on amplifier = phase modulation.

G8A05

What type of modulation varies the instantaneous power level of the RF signal?

  1. A. Power modulation
  2. B. Phase modulation
  3. C. Frequency modulation
  4. D. Amplitude modulation
Show the answer and explanation

Answer: D. Amplitude modulation

Amplitude modulation varies the strength (amplitude, and therefore instantaneous power) of the RF signal. Phase and frequency modulation keep the amplitude constant.

Tip: AM varies amplitude, so power varies.

G8A06

Which of the following is characteristic of QPSK31?

  1. A. It is sideband sensitive
  2. B. Its encoding provides error correction
  3. C. Its bandwidth is approximately the same as BPSK31
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

QPSK31 is sideband sensitive (you must use the right sideband), adds error correction to its encoding, and takes about the same bandwidth as BPSK31. So all the statements are true.

Tip: QPSK31: same width as BPSK31, plus FEC.

G8A07

Which of the following phone emissions uses the narrowest bandwidth?

  1. A. Single sideband
  2. B. Vestigial sideband
  3. C. Phase modulation
  4. D. Frequency modulation
Show the answer and explanation

Answer: A. Single sideband

Single sideband sends only one sideband and no carrier, so it needs only about 2 to 3 kHz. Vestigial sideband, PM, and FM all occupy more spectrum.

Tip: SSB = skinniest phone signal.

G8A08

Which of the following is an effect of overmodulation?

  1. A. Insufficient audio
  2. B. Insufficient bandwidth
  3. C. Frequency drift
  4. D. Excessive bandwidth
Show the answer and explanation

Answer: D. Excessive bandwidth

Overmodulation distorts the signal and creates splatter, spreading energy well beyond the normal bandwidth. That excessive bandwidth interferes with nearby stations.

Tip: Overmodulation = splatter = too wide.

G8A09

What type of modulation is used by FT8?

  1. A. 8-tone frequency shift keying
  2. B. Vestigial sideband
  3. C. Amplitude compressed AM
  4. D. 8-bit direct sequence spread spectrum
Show the answer and explanation

Answer: A. 8-tone frequency shift keying

FT8 uses 8-tone frequency shift keying (8-FSK). The 8 in the name refers to the eight tones.

Tip: FT8 = 8 tones.

G8A10

What is meant by the term “flat-topping,” when referring to an amplitude-modulated phone signal?

  1. A. Signal distortion caused by insufficient collector current
  2. B. The transmitter's automatic level control (ALC) is properly adjusted
  3. C. Signal distortion caused by excessive drive or speech levels
  4. D. The transmitter's carrier is properly suppressed
Show the answer and explanation

Answer: C. Signal distortion caused by excessive drive or speech levels

Flat-topping is distortion that happens when excessive drive or speech levels push the transmitter past its limits, clipping the signal peaks flat. It is a sign of overdriving, not proper adjustment.

Tip: Too much drive flattens the peaks.

G8A11

What is the modulation envelope of an AM signal?

  1. A. The waveform created by connecting the peak values of the modulated signal
  2. B. The carrier frequency that contains the signal
  3. C. Spurious signals that envelop nearby frequencies
  4. D. The bandwidth of the modulated signal
Show the answer and explanation

Answer: A. The waveform created by connecting the peak values of the modulated signal

The modulation envelope is the outline traced by connecting the peaks of the modulated RF waveform. For AM, it follows the shape of the audio.

Tip: Envelope = line connecting the peaks.

G8A12

What is QPSK modulation?

  1. A. Modulation using quasi-parallel to serial conversion to reduce bandwidth
  2. B. Modulation using quadra-pole sideband keying to generate spread spectrum signals
  3. C. Modulation using Fast Fourier Transforms to generate frequencies at the first, second, third, and fourth harmonics of the carrier frequency to improve noise immunity
  4. D. Modulation in which digital data is transmitted using 0-, 90-, 180- and 270-degrees phase shift to represent pairs of bits
Show the answer and explanation

Answer: D. Modulation in which digital data is transmitted using 0-, 90-, 180- and 270-degrees phase shift to represent pairs of bits

QPSK (quadrature phase shift keying) uses four phase shifts, 0, 90, 180, and 270 degrees, each representing a pair of bits. That sends two bits per symbol.

Tip: Quadrature = four phases, two bits each.

G8A13

What is a link budget?

  1. A. The financial costs associated with operating a radio link
  2. B. The sum of antenna gains minus system losses
  3. C. The sum of transmit power and antenna gains minus system losses as seen at the receiver
  4. D. The difference between transmit power and receiver sensitivity
Show the answer and explanation

Answer: C. The sum of transmit power and antenna gains minus system losses as seen at the receiver

A link budget adds transmit power and antenna gains, then subtracts all system losses, to find the signal level at the receiver. Antenna gains minus losses alone leaves out the transmit power.

Tip: Power plus gains minus losses = received level.

G8A14

What is link margin?

  1. A. The opposite of fade margin
  2. B. The difference between received power level and minimum required signal level at the input to the receiver
  3. C. Transmit power minus receiver sensitivity
  4. D. Receiver sensitivity plus 3 dB
Show the answer and explanation

Answer: B. The difference between received power level and minimum required signal level at the input to the receiver

Link margin is how much the received signal level exceeds the minimum level the receiver needs. More margin means the link tolerates more fading.

Tip: Margin = received minus required.

G8B

Frequency changing; bandwidths of various modes; deviation; intermodulation

G8B01

Which mixer input is varied or tuned to convert signals of different frequencies to an intermediate frequency (IF)?

  1. A. Image frequency
  2. B. Local oscillator
  3. C. RF input
  4. D. Beat frequency oscillator
Show the answer and explanation

Answer: B. Local oscillator

In a superheterodyne receiver, the local oscillator is tuned so that mixing it with each incoming signal produces the fixed intermediate frequency. The RF input is whatever signal arrives.

Tip: Tune the LO to land on the IF.

G8B02

What is the term for interference from a signal at twice the IF frequency from the desired signal?

  1. A. Quadrature response
  2. B. Image response
  3. C. Mixer interference
  4. D. Intermediate interference
Show the answer and explanation

Answer: B. Image response

An image is an unwanted signal located twice the IF away from the desired signal, on the other side of the local oscillator. It also mixes down to the IF, causing image response.

Tip: Image sits 2 x IF away.

G8B03

What is another term for the mixing of two RF signals?

  1. A. Heterodyning
  2. B. Synthesizing
  3. C. Frequency inversion
  4. D. Phase inversion
Show the answer and explanation

Answer: A. Heterodyning

Mixing two RF signals to produce sum and difference frequencies is called heterodyning. That is where the superheterodyne receiver gets its name.

Tip: Mixing = heterodyning.

G8B04

What is the stage in a VHF FM transmitter that generates a harmonic of a lower frequency signal to reach the desired operating frequency?

  1. A. Mixer
  2. B. Reactance modulator
  3. C. Balanced converter
  4. D. Multiplier
Show the answer and explanation

Answer: D. Multiplier

A multiplier stage generates a harmonic of a lower frequency signal, multiplying it up to the operating frequency. Many VHF FM transmitters use multipliers this way.

Tip: Multiplier multiplies frequency up.

G8B05

Which intermodulation products are closest to the original signal frequencies?

  1. A. Second harmonics
  2. B. Even-order
  3. C. Odd-order
  4. D. Intercept point
Show the answer and explanation

Answer: C. Odd-order

Odd-order products such as 2F1-F2 and 2F2-F1 fall close to the original frequencies, often inside the band. Even-order products land far away, where they are easily filtered.

Tip: Odd-order products land close by.

G8B06

What is the total bandwidth of an FM phone transmission having 5 kHz deviation and 3 kHz modulating frequency?

  1. A. 3 kHz
  2. B. 5 kHz
  3. C. 8 kHz
  4. D. 16 kHz
Show the answer and explanation

Answer: D. 16 kHz

Use Carson's rule: bandwidth = 2 x (deviation + modulating frequency) = 2 x (5 kHz + 3 kHz) = 16 kHz.

Tip: Carson's rule: 2 x (deviation + audio).

G8B07

What is the frequency deviation for a 12.21 MHz reactance modulated oscillator in a 5 kHz deviation, 146.52 MHz FM phone transmitter?

  1. A. 101.75 Hz
  2. B. 416.7 Hz
  3. C. 5 kHz
  4. D. 60 kHz
Show the answer and explanation

Answer: B. 416.7 Hz

The multiplication factor is 146.52 MHz / 12.21 MHz = 12. The oscillator deviation is 5 kHz / 12 = 416.7 Hz, since the multiplier stages multiply the deviation by 12.

Tip: Divide deviation by the multiplication factor.

G8B08

Why is it important to know the duty cycle of the mode you are using when transmitting?

  1. A. To aid in tuning your transmitter
  2. B. Some modes have high duty cycles that could exceed the transmitter's average power rating
  3. C. To allow time for the other station to break in during a transmission
  4. D. To prevent overmodulation
Show the answer and explanation

Answer: B. Some modes have high duty cycles that could exceed the transmitter's average power rating

Modes like FM, RTTY, and many digital modes transmit at full power continuously (high duty cycle). This can exceed a transmitter's average power rating and overheat it, so you may need to reduce power.

Tip: High duty cycle modes can overheat transmitters.

G8B09

Why is it good to match receiver bandwidth to the bandwidth of the operating mode?

  1. A. It is required by FCC rules
  2. B. It minimizes power consumption in the receiver
  3. C. It improves impedance matching of the antenna
  4. D. It results in the best signal-to-noise ratio
Show the answer and explanation

Answer: D. It results in the best signal-to-noise ratio

A receiver bandwidth matched to the signal passes all of the signal while rejecting extra noise outside it. That gives the best signal-to-noise ratio.

Tip: Match the filter, maximize signal-to-noise.

G8B10

What is the relationship between transmitted symbol rate and bandwidth?

  1. A. Symbol rate and bandwidth are not related
  2. B. Higher symbol rates require wider bandwidth
  3. C. Lower symbol rates require wider bandwidth
  4. D. Bandwidth is half the symbol rate
Show the answer and explanation

Answer: B. Higher symbol rates require wider bandwidth

Sending symbols faster requires more bandwidth. Higher symbol rates require wider bandwidth, while slow modes like PSK31 stay very narrow.

Tip: Faster symbols need wider bandwidth.

G8B11

What combination of a mixer's Local Oscillator (LO) and RF input frequencies is found in the output?

  1. A. The ratio
  2. B. The average
  3. C. The sum and difference
  4. D. The arithmetic product
Show the answer and explanation

Answer: C. The sum and difference

A mixer outputs the sum and the difference of its LO and RF input frequencies, along with the original signals. The receiver filters out the one it wants as the IF.

Tip: Mixer output = sum and difference.

G8B12

What process combines two signals in a non-linear circuit to produce unwanted spurious outputs?

  1. A. Intermodulation
  2. B. Heterodyning
  3. C. Detection
  4. D. Rolloff
Show the answer and explanation

Answer: A. Intermodulation

Intermodulation occurs when two signals combine in a non-linear circuit and produce unwanted spurious frequencies. Heterodyning is mixing on purpose to get a desired output.

Tip: Unwanted mixing = intermodulation.

G8B13

Which of the following is an odd-order intermodulation product of frequencies F1 and F2?

  1. A. 5F1-3F2
  2. B. 3F1-F2
  3. C. 2F1-F2
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. 2F1-F2

The order of an intermodulation product is the sum of the multipliers. For 2F1-F2 that is 2 + 1 = 3, which is odd. 5F1-3F2 gives 8 and 3F1-F2 gives 4, both even.

Tip: Add the coefficients; odd total = odd order.

G8C

Digital emission modes

G8C02

Which digital mode is used as a low-power beacon for assessing HF propagation?

  1. A. WSPR
  2. B. MFSK16
  3. C. PSK31
  4. D. SSB-SC
Show the answer and explanation

Answer: A. WSPR

WSPR (Weak Signal Propagation Reporter) stations send low-power beacon transmissions that are reported online. This shows where your signal is being heard and helps assess HF propagation.

Tip: WSPR = whisper beacon for propagation.

G8C03

What part of a packet radio frame contains the routing and handling information?

  1. A. Directory
  2. B. Preamble
  3. C. Header
  4. D. Trailer
Show the answer and explanation

Answer: C. Header

The header of a packet radio frame holds the routing and handling information, such as source and destination addresses. The data follows the header.

Tip: Header holds the address.

G8C04

Which of the following describes Baudot code?

  1. A. A 7-bit code with start, stop, and parity bits
  2. B. A code using error detection and correction
  3. C. A 5-bit code with additional start and stop bits
  4. D. A code using SELCAL and LISTEN
Show the answer and explanation

Answer: C. A 5-bit code with additional start and stop bits

Baudot is a 5-bit code with additional start and stop bits, used for RTTY. ASCII is the 7-bit code.

Tip: Baudot = 5 bits, used for RTTY.

G8C05

In an ARQ mode, what is meant by a NAK response to a transmitted packet?

  1. A. Request retransmission of the packet
  2. B. Packet was received without error
  3. C. Receiving station connected and ready for transmissions
  4. D. Entire file received correctly
Show the answer and explanation

Answer: A. Request retransmission of the packet

In ARQ (automatic repeat request) modes, a NAK (negative acknowledgment) tells the sender the packet had errors, requesting retransmission of the packet. An ACK means it was received correctly.

Tip: NAK = not okay, send it again.

G8C06

What action results from a failure to exchange information due to excessive transmission attempts when using an ARQ mode?

  1. A. The checksum overflows
  2. B. The connection is dropped
  3. C. Packets will be routed incorrectly
  4. D. Encoding reverts to the default character set
Show the answer and explanation

Answer: B. The connection is dropped

If an ARQ link keeps failing and retries hit their limit, the connection is dropped. The stations give up rather than retrying forever.

Tip: Too many retries = connection dropped.

G8C07

Which of the following narrow-band digital modes can receive signals with very low signal-to-noise ratios?

  1. A. MSK144
  2. B. FT8
  3. C. AMTOR
  4. D. MFSK32
Show the answer and explanation

Answer: B. FT8

FT8 is a narrow-band weak-signal mode that can decode signals well below the noise level, around -20 dB SNR. That makes it popular for weak-signal contacts.

Tip: FT8 digs signals out of the noise.

G8C08

Which of the following statements is true about PSK31?

  1. A. Upper case letters are sent with more power
  2. B. Upper case letters use longer Varicode bit sequences and thus slow down transmission
  3. C. Error correction is used to ensure accurate message reception
  4. D. Higher power is needed as compared to RTTY for similar error rates
Show the answer and explanation

Answer: B. Upper case letters use longer Varicode bit sequences and thus slow down transmission

PSK31 uses Varicode, which gives common lower case letters short bit sequences. Upper case letters use longer Varicode sequences and thus slow down transmission.

Tip: Capitals take longer in PSK31.

G8C09

Which is true of mesh network microwave nodes?

  1. A. Having more nodes increases signal strengths
  2. B. If one node fails, a packet may still reach its target station via an alternate node
  3. C. Links between two nodes in a network may have different frequencies and bandwidths
  4. D. More nodes reduce overall microwave out of band interference
Show the answer and explanation

Answer: B. If one node fails, a packet may still reach its target station via an alternate node

A mesh network has many interconnected nodes, so if one node fails, a packet may still reach its target station via an alternate node. This redundancy is the main strength of mesh networks.

Tip: Mesh: routes around a dead node.

G8C10

How does forward error correction (FEC) allow the receiver to correct data errors?

  1. A. By controlling transmitter output power for optimum signal strength
  2. B. By using the Varicode character set
  3. C. By transmitting redundant information with the data
  4. D. By using a parity bit with each character
Show the answer and explanation

Answer: C. By transmitting redundant information with the data

Forward error correction transmits redundant information along with the data. The receiver uses that extra information to fix errors without asking for a retransmission.

Tip: FEC sends extra data to fix errors.

G8C11

How are the two separate frequencies of a Frequency Shift Keyed (FSK) signal identified?

  1. A. Dot and dash
  2. B. On and off
  3. C. High and low
  4. D. Mark and space
Show the answer and explanation

Answer: D. Mark and space

The two frequencies of an FSK signal are called mark and space. These terms come from early telegraph and teletype systems.

Tip: FSK tones: mark and space.

G8C12

Which type of code is used for sending characters in a PSK31 signal?

  1. A. Varicode
  2. B. Viterbi
  3. C. Volumetric
  4. D. Binary
Show the answer and explanation

Answer: A. Varicode

PSK31 uses Varicode, a variable-length code where common characters get shorter bit patterns. This keeps the signal fast and narrow.

Tip: PSK31 speaks Varicode.

G8C13

What is indicated on a waterfall display by one or more vertical lines on either side of a data mode or RTTY signal?

  1. A. Long path propagation
  2. B. Backscatter propagation
  3. C. Insufficient modulation
  4. D. Overmodulation
Show the answer and explanation

Answer: D. Overmodulation

Vertical lines on either side of a digital or RTTY signal on a waterfall are spurious sidebands caused by overmodulation. Reduce audio drive until they disappear.

Tip: Side lines on the waterfall = too much audio.

G8C14

Which of the following describes a waterfall display?

  1. A. Frequency is horizontal, signal strength is vertical, time is intensity
  2. B. Frequency is vertical, signal strength is intensity, time is horizontal
  3. C. Frequency is horizontal, signal strength is intensity, time is vertical
  4. D. Frequency is vertical, signal strength is horizontal, time is intensity
Show the answer and explanation

Answer: C. Frequency is horizontal, signal strength is intensity, time is vertical

On a waterfall display, frequency runs horizontally, signal strength is shown by color or brightness (intensity), and time scrolls vertically. Older signals flow downward like a waterfall.

Tip: Across = frequency, down = time, bright = strong.

G8C15

What does an FT8 signal report of +3 mean?

  1. A. The signal is 3 times the noise level of an equivalent SSB signal
  2. B. The signal is S3 (weak signals)
  3. C. The signal-to-noise ratio is equivalent to +3dB in a 2.5 kHz bandwidth
  4. D. The signal is 3 dB over S9
Show the answer and explanation

Answer: C. The signal-to-noise ratio is equivalent to +3dB in a 2.5 kHz bandwidth

FT8 reports signal-to-noise ratio as if measured in a 2.5 kHz bandwidth. A report of +3 means the SNR is equivalent to +3 dB in that 2.5 kHz bandwidth, not an S-meter reading.

Tip: FT8 report = SNR in 2.5 kHz.

G8C16

Which of the following provide digital voice modes?

  1. A. WSPR, MFSK16, and EasyPAL
  2. B. FT8, FT4, and FST4
  3. C. Winlink, PACTOR II, and PACTOR III
  4. D. DMR, D-STAR, and SystemFusion
Show the answer and explanation

Answer: D. DMR, D-STAR, and SystemFusion

DMR, D-STAR, and System Fusion are all digital voice modes common on VHF/UHF. The other groups are data, image, or weak-signal modes.

Tip: DMR, D-STAR, Fusion = digital voice.

Practice G8 with scoring Take a 35-question practice exam