Ham Tech Prep

General › G6

G6 Circuit Components

23 questions in the pool. Your exam will include 2, one from each group below.

Practice G6 now

G6A

Resistors; capacitors; inductors; rectifiers; solid-state diodes and transistors; vacuum tubes; batteries

G6A01

What is the minimum allowable discharge voltage for maximum life of a standard 12-volt lead-acid battery?

  1. A. 6 volts
  2. B. 8.5 volts
  3. C. 10.5 volts
  4. D. 12 volts
Show the answer and explanation

Answer: C. 10.5 volts

Discharging a 12-volt lead-acid battery below about 10.5 volts shortens its life. Stop discharging at 10.5 V to get the most charge cycles.

Tip: Lead-acid: stop at 10.5 volts.

G6A02

What is an advantage of batteries with low internal resistance?

  1. A. Long life
  2. B. High discharge current
  3. C. High voltage
  4. D. Rapid recharge
Show the answer and explanation

Answer: B. High discharge current

Low internal resistance means less voltage is lost inside the battery, so it can deliver high current. That is useful for transmitting, which draws heavy current.

Tip: Low internal resistance = high current.

G6A03

What is the approximate forward threshold voltage of a germanium diode?

  1. A. 0.1 volt
  2. B. 0.3 volts
  3. C. 0.7 volts
  4. D. 1.0 volts
Show the answer and explanation

Answer: B. 0.3 volts

A germanium diode starts to conduct at about 0.3 volts forward bias. Silicon diodes need about 0.7 volts.

Tip: Germanium 0.3, silicon 0.7.

G6A04

Which of the following is characteristic of an electrolytic capacitor?

  1. A. Tight tolerance
  2. B. Much less leakage than any other type
  3. C. High capacitance for a given volume
  4. D. Inexpensive RF capacitor
Show the answer and explanation

Answer: C. High capacitance for a given volume

Electrolytic capacitors pack a large capacitance into a small package. They have loose tolerance and relatively high leakage, and are not suited for RF use.

Tip: Electrolytic = big capacitance, small size.

G6A05

What is the approximate forward threshold voltage of a silicon junction diode?

  1. A. 0.1 volt
  2. B. 0.3 volts
  3. C. 0.7 volts
  4. D. 1.0 volts
Show the answer and explanation

Answer: C. 0.7 volts

A silicon junction diode begins to conduct at about 0.7 volts forward bias. Germanium diodes need only about 0.3 volts.

Tip: Silicon 0.7, germanium 0.3.

G6A06

Why should wire-wound resistors not be used in RF circuits?

  1. A. The resistor's tolerance value would not be adequate
  2. B. The resistor's inductance could make circuit performance unpredictable
  3. C. The resistor could overheat
  4. D. The resistor's internal capacitance would detune the circuit
Show the answer and explanation

Answer: B. The resistor's inductance could make circuit performance unpredictable

A wire-wound resistor is a coil of wire, so it has inductance. At radio frequencies that inductance adds reactance and makes the circuit behave unpredictably.

Tip: Wire-wound = coil = unwanted inductance.

G6A07

What are the operating points for a bipolar transistor used as a switch?

  1. A. Saturation and cutoff
  2. B. The active region (between cutoff and saturation)
  3. C. Peak and valley current points
  4. D. Enhancement and depletion modes
Show the answer and explanation

Answer: A. Saturation and cutoff

A transistor used as a switch is driven fully on (saturation) or fully off (cutoff). The active region in between is used for amplifiers, not switches.

Tip: Switch: all on (saturation) or all off (cutoff).

G6A08

Which of the following is characteristic of low voltage ceramic capacitors?

  1. A. Tight tolerance
  2. B. High stability
  3. C. High capacitance for given volume
  4. D. Comparatively low cost
Show the answer and explanation

Answer: D. Comparatively low cost

Low voltage ceramic capacitors are popular mainly because they are cheap. They do not have tight tolerance, high stability, or high capacitance per volume.

Tip: Ceramic caps are cheap.

G6A09

Which of the following describes MOSFET construction?

  1. A. The gate is formed by a back-biased junction
  2. B. The gate is separated from the channel by a thin insulating layer
  3. C. The source is separated from the drain by a thin insulating layer
  4. D. The source is formed by depositing metal on silicon
Show the answer and explanation

Answer: B. The gate is separated from the channel by a thin insulating layer

In a MOSFET (metal oxide semiconductor FET), the gate is separated from the channel by a thin insulating oxide layer. That insulation gives it a very high input impedance.

Tip: MOSFET gate is insulated by oxide.

G6A10

Which element of a vacuum tube regulates the flow of electrons between cathode and plate?

  1. A. Control grid
  2. B. Suppressor grid
  3. C. Screen grid
  4. D. Trigger electrode
Show the answer and explanation

Answer: A. Control grid

The control grid sits between the cathode and plate, and its voltage controls how many electrons reach the plate. That is how a tube amplifies.

Tip: Control grid controls electron flow.

G6A11

What happens when an inductor is operated above its self-resonant frequency?

  1. A. Its reactance increases
  2. B. Harmonics are generated
  3. C. It becomes capacitive
  4. D. Catastrophic failure is likely
Show the answer and explanation

Answer: C. It becomes capacitive

Every inductor has some capacitance between its turns. Above its self-resonant frequency, that capacitance dominates and the inductor behaves like a capacitor.

Tip: Above self-resonance, L acts like C.

G6A12

What is the primary purpose of a screen grid in a vacuum tube?

  1. A. To reduce grid-to-plate capacitance
  2. B. To increase efficiency
  3. C. To increase the control grid resistance
  4. D. To decrease plate resistance
Show the answer and explanation

Answer: A. To reduce grid-to-plate capacitance

The screen grid sits between the control grid and plate and acts as a shield. It reduces grid-to-plate capacitance, which helps prevent unwanted oscillation.

Tip: Screen grid screens grid from plate.

G6B

Analog and digital integrated circuits (ICs); microwave ICs (MMICs); display devices; RF connectors; ferrite cores

G6B01

What determines the performance of a ferrite core at different frequencies?

  1. A. Its conductivity
  2. B. Its thickness
  3. C. The composition, or “mix,” of materials used
  4. D. The ratio of outer diameter to inner diameter
Show the answer and explanation

Answer: C. The composition, or “mix,” of materials used

A ferrite core's performance at different frequencies depends on its mix, the blend of materials it is made from. Different mixes are chosen for different frequency ranges.

Tip: Ferrite: the mix sets the frequency range.

G6B02

What is meant by the term MMIC?

  1. A. Multi-Mode Integrated Circuit
  2. B. Monolithic Microwave Integrated Circuit
  3. C. Metal Monolayer Integrated Circuit
  4. D. Mode Modulated Integrated Circuit
Show the answer and explanation

Answer: B. Monolithic Microwave Integrated Circuit

MMIC stands for Monolithic Microwave Integrated Circuit. It is a small single-chip amplifier or other circuit for VHF through microwave frequencies.

Tip: MMIC = Monolithic Microwave IC.

G6B03

Which of the following is an advantage of CMOS integrated circuits compared to TTL integrated circuits?

  1. A. Low power consumption
  2. B. High power handling capability
  3. C. Better suited for RF amplification
  4. D. Better suited for power supply regulation
Show the answer and explanation

Answer: A. Low power consumption

CMOS chips draw very little power, especially when not switching. That low power consumption is their main advantage over TTL chips.

Tip: CMOS = low power.

G6B04

What is a typical upper frequency limit for low SWR operation of 50-ohm BNC connectors?

  1. A. 50 MHz
  2. B. 500 MHz
  3. C. 4 GHz
  4. D. 40 GHz
Show the answer and explanation

Answer: C. 4 GHz

BNC connectors keep a low SWR up to about 4 GHz. Above that, connectors like type N or SMA work better.

Tip: BNC is good to about 4 GHz.

G6B05

What is an advantage of using a ferrite core toroidal inductor?

  1. A. Large values of inductance may be obtained
  2. B. The magnetic properties of the core may be optimized for a specific range of frequencies
  3. C. Most of the magnetic field is contained in the core
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Ferrite toroids give large inductance in a small size, the core mix can be chosen for a frequency range, and the core holds most of the magnetic field. So all the choices are correct.

Tip: Toroid: big L, tunable mix, self-shielding.

G6B06

What kind of device is an integrated circuit operational amplifier?

  1. A. Digital
  2. B. MMIC
  3. C. Programmable Logic
  4. D. Analog
Show the answer and explanation

Answer: D. Analog

An op-amp is an analog device that amplifies continuously varying voltages. It is not a digital or programmable logic part.

Tip: Op-amp = analog amplifier.

G6B07

Which of the following describes a type N connector?

  1. A. A moisture-resistant RF connector useful to 10 GHz
  2. B. A small bayonet connector used for data circuits
  3. C. A low noise figure VHF connector
  4. D. A nickel plated version of the PL-259
Show the answer and explanation

Answer: A. A moisture-resistant RF connector useful to 10 GHz

A type N connector is a rugged, moisture-resistant, threaded RF connector usable up to about 10 GHz. It is popular for outdoor and VHF/UHF use.

Tip: Type N: weatherproof, good to 10 GHz.

G6B08

How is an LED biased when emitting light?

  1. A. In the tunnel-effect region
  2. B. At the Zener voltage
  3. C. Reverse biased
  4. D. Forward biased
Show the answer and explanation

Answer: D. Forward biased

An LED gives off light when it is forward biased and current flows through it. A reverse-biased LED does not conduct or light.

Tip: LED lights when forward biased.

G6B10

How does a ferrite bead or core reduce common-mode RF current on the shield of a coaxial cable?

  1. A. By creating an impedance in the current's path
  2. B. It converts common-mode current to differential mode current
  3. C. By creating an out-of-phase current to cancel the common-mode current
  4. D. Ferrites expel magnetic fields
Show the answer and explanation

Answer: A. By creating an impedance in the current's path

A ferrite bead or core adds impedance to the common-mode current flowing on the outside of the coax shield. That impedance chokes off the unwanted current.

Tip: Ferrite chokes current with impedance.

G6B11

What is an SMA connector?

  1. A. A type-S to type-M adaptor
  2. B. A small threaded connector suitable for signals up to several GHz
  3. C. A connector designed for serial multiple access signals
  4. D. A type of push-on connector intended for high-voltage applications
Show the answer and explanation

Answer: B. A small threaded connector suitable for signals up to several GHz

An SMA (SubMiniature version A) connector is a small threaded connector good for signals up to several GHz. It is common on handheld radios and SDRs.

Tip: SMA: small, threaded, GHz-capable.

G6B12

Which of these connector types is commonly used for low frequency or dc signal connections to a transceiver?

  1. A. PL-259
  2. B. BNC
  3. C. RCA Phono
  4. D. Type N
Show the answer and explanation

Answer: C. RCA Phono

RCA phono connectors are common for audio, low frequency, and DC connections such as keying lines to a transceiver. PL-259, BNC, and type N are RF connectors.

Tip: RCA phono for audio and control lines.

Practice G6 with scoring Take a 35-question practice exam