Ham Tech Prep

General › G5

G5 Electrical Principles

40 questions in the pool. Your exam will include 3, one from each group below.

Practice G5 now

G5A

Reactance; inductance; capacitance; impedance; impedance transformation; resonance

G5A01

What happens when inductive and capacitive reactance are equal in a series LC circuit?

  1. A. Resonance causes impedance to be very high
  2. B. Impedance is equal to the geometric mean of the inductance and capacitance
  3. C. Resonance causes impedance to be very low
  4. D. Impedance is equal to the arithmetic mean of the inductance and capacitance
Show the answer and explanation

Answer: C. Resonance causes impedance to be very low

In a series LC circuit at resonance, the inductive and capacitive reactances cancel each other. Only the small resistance is left, so impedance is very low. A parallel LC circuit is the one with very high impedance at resonance.

Tip: Series resonance = low impedance.

G5A02

What is reactance?

  1. A. Opposition to the flow of direct current caused by resistance
  2. B. Opposition to the flow of alternating current caused by capacitance or inductance
  3. C. Reinforcement of the flow of direct current caused by resistance
  4. D. Reinforcement of the flow of alternating current caused by capacitance or inductance
Show the answer and explanation

Answer: B. Opposition to the flow of alternating current caused by capacitance or inductance

Reactance is the opposition that capacitors and inductors give to alternating current. Opposition caused by resistance is just resistance, not reactance.

Tip: Reactance comes from L and C, with AC.

G5A03

Which of the following is opposition to the flow of alternating current in an inductor?

  1. A. Conductance
  2. B. Reluctance
  3. C. Admittance
  4. D. Reactance
Show the answer and explanation

Answer: D. Reactance

An inductor opposes AC with inductive reactance. Reluctance is a magnetic circuit term, and conductance and admittance describe how easily current flows, not opposition.

Tip: Inductor opposes AC with reactance.

G5A04

Which of the following is opposition to the flow of alternating current in a capacitor?

  1. A. Conductance
  2. B. Reluctance
  3. C. Reactance
  4. D. Admittance
Show the answer and explanation

Answer: C. Reactance

A capacitor opposes AC with capacitive reactance. Conductance and admittance measure ease of current flow, and reluctance belongs to magnetic circuits.

Tip: Capacitor opposes AC with reactance.

G5A05

How does an inductor react to AC?

  1. A. As the frequency of the applied AC increases, the reactance decreases
  2. B. As the amplitude of the applied AC increases, the reactance increases
  3. C. As the amplitude of the applied AC increases, the reactance decreases
  4. D. As the frequency of the applied AC increases, the reactance increases
Show the answer and explanation

Answer: D. As the frequency of the applied AC increases, the reactance increases

Inductive reactance rises with frequency: XL = 2 x pi x f x L. Higher frequency means more opposition. The signal's amplitude does not change reactance.

Tip: Inductor: higher frequency, higher reactance.

G5A06

How does a capacitor react to AC?

  1. A. As the frequency of the applied AC increases, the reactance decreases
  2. B. As the frequency of the applied AC increases, the reactance increases
  3. C. As the amplitude of the applied AC increases, the reactance increases
  4. D. As the amplitude of the applied AC increases, the reactance decreases
Show the answer and explanation

Answer: A. As the frequency of the applied AC increases, the reactance decreases

Capacitive reactance falls as frequency rises: XC = 1 / (2 x pi x f x C). A capacitor passes high frequencies more easily. Amplitude does not change reactance.

Tip: Capacitor: higher frequency, lower reactance.

G5A07

What is the term for the inverse of impedance?

  1. A. Conductance
  2. B. Susceptance
  3. C. Reluctance
  4. D. Admittance
Show the answer and explanation

Answer: D. Admittance

Admittance is the inverse of impedance (Y = 1/Z). Conductance is the inverse of resistance only, and susceptance is the inverse of reactance only.

Tip: Admittance admits current: Y = 1/Z.

G5A08

What is impedance?

  1. A. The ratio of current to voltage
  2. B. The product of current and voltage
  3. C. The ratio of voltage to current
  4. D. The product of current and reactance
Show the answer and explanation

Answer: C. The ratio of voltage to current

Impedance is the total opposition to AC, found by dividing voltage by current (Z = E / I). It is the AC version of Ohm's law for resistance.

Tip: Z = E / I, like R = E / I.

G5A09

What unit is used to measure reactance?

  1. A. Farad
  2. B. Ohm
  3. C. Ampere
  4. D. Siemens
Show the answer and explanation

Answer: B. Ohm

Reactance is opposition to current, so like resistance it is measured in ohms. Farads measure capacitance and siemens measure conductance or admittance.

Tip: All opposition is measured in ohms.

G5A10

Which of the following devices can be used for impedance matching at radio frequencies?

  1. A. A transformer
  2. B. A Pi-network
  3. C. A length of transmission line
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Transformers, pi-networks, and specific lengths of transmission line can all transform one impedance to another at RF. So all of the listed devices work for impedance matching.

Tip: Transformer, pi-net, or coax stub: all match.

G5A11

What letter is used to represent reactance?

  1. A. Z
  2. B. X
  3. C. B
  4. D. Y
Show the answer and explanation

Answer: B. X

Reactance is written as X, such as XL for inductive and XC for capacitive reactance. Z stands for impedance, B for susceptance, and Y for admittance.

Tip: X marks reactance.

G5A12

What occurs in an LC circuit at resonance?

  1. A. Current and voltage are equal
  2. B. Resistance is cancelled
  3. C. The circuit radiates all its energy in the form of radio waves
  4. D. Inductive reactance and capacitive reactance cancel
Show the answer and explanation

Answer: D. Inductive reactance and capacitive reactance cancel

At resonance, inductive reactance and capacitive reactance are equal and opposite, so they cancel. Only resistance remains in the circuit.

Tip: Resonance: XL = XC, they cancel.

G5B

The decibel; current and voltage dividers; electrical power calculations; sine wave root-mean-square (RMS) values; PEP calculations

G5B01

What dB change represents a factor of two increase or decrease in power?

  1. A. Approximately 2 dB
  2. B. Approximately 3 dB
  3. C. Approximately 6 dB
  4. D. Approximately 9 dB
Show the answer and explanation

Answer: B. Approximately 3 dB

A 3 dB change is about a doubling or halving of power, since 10 x log(2) = 3.01 dB. A 6 dB change is a factor of four in power.

Tip: 3 dB = double or half the power.

G5B02

How does the total current relate to the individual currents in a circuit of parallel resistors?

  1. A. It equals the average of the branch currents
  2. B. It decreases as more parallel branches are added to the circuit
  3. C. It equals the sum of the currents through each branch
  4. D. It is the sum of the reciprocal of each individual voltage drop
Show the answer and explanation

Answer: C. It equals the sum of the currents through each branch

In a parallel circuit each branch draws its own current, and the total current is the sum of all the branch currents. Adding branches increases total current.

Tip: Parallel branches: currents add up.

G5B03

How many watts of electrical power are consumed if 400 VDC is supplied to an 800-ohm load?

  1. A. 0.5 watts
  2. B. 200 watts
  3. C. 400 watts
  4. D. 3200 watts
Show the answer and explanation

Answer: B. 200 watts

Use P = E^2 / R. P = 400 V x 400 V / 800 ohms = 160,000 / 800 = 200 W.

Tip: Voltage and resistance known: P = E squared / R.

G5B04

How many watts of electrical power are consumed by a 12 VDC light bulb that draws 0.2 amperes?

  1. A. 2.4 watts
  2. B. 24 watts
  3. C. 6 watts
  4. D. 60 watts
Show the answer and explanation

Answer: A. 2.4 watts

Use P = E x I. P = 12 V x 0.2 A = 2.4 W.

Tip: Power = volts times amps.

G5B05

How many watts are consumed when a current of 7.0 milliamperes flows through a 1,250-ohm resistance?

  1. A. Approximately 61 milliwatts
  2. B. Approximately 61 watts
  3. C. Approximately 11 milliwatts
  4. D. Approximately 11 watts
Show the answer and explanation

Answer: A. Approximately 61 milliwatts

Use P = I^2 x R. P = 0.007 A x 0.007 A x 1,250 ohms = 0.000049 x 1,250 = 0.061 W, about 61 milliwatts.

Tip: Current and resistance known: P = I squared x R.

G5B06

What is the PEP produced by 200 volts peak-to-peak across a 50-ohm dummy load?

  1. A. 1.4 watts
  2. B. 100 watts
  3. C. 353.5 watts
  4. D. 400 watts
Show the answer and explanation

Answer: B. 100 watts

200 V peak-to-peak is 100 V peak. RMS = 100 x 0.707 = 70.7 V. PEP = E^2 / R = 70.7 x 70.7 / 50 = 5,000 / 50 = 100 W.

Tip: P-P to peak (/2), to RMS (x 0.707), then E squared / R.

G5B07

What value of an AC signal produces the same power dissipation in a resistor as a DC voltage of the same value?

  1. A. The peak-to-peak value
  2. B. The peak value
  3. C. The RMS value
  4. D. The reciprocal of the RMS value
Show the answer and explanation

Answer: C. The RMS value

The RMS (root mean square) value of an AC voltage heats a resistor exactly as much as the same DC voltage. That is why AC power is calculated with RMS values.

Tip: RMS = DC-equivalent heating value.

G5B08

What is the peak-to-peak voltage of a sine wave with an RMS voltage of 120 volts?

  1. A. 84.8 volts
  2. B. 169.7 volts
  3. C. 240.0 volts
  4. D. 339.4 volts
Show the answer and explanation

Answer: D. 339.4 volts

Peak = RMS x 1.414 = 120 x 1.414 = 169.7 V. Peak-to-peak is twice the peak: 2 x 169.7 = 339.4 V. 169.7 V is only the peak value.

Tip: RMS x 1.414 x 2 = peak-to-peak.

G5B09

What is the RMS voltage of a sine wave with a value of 17 volts peak?

  1. A. 8.5 volts
  2. B. 12 volts
  3. C. 24 volts
  4. D. 34 volts
Show the answer and explanation

Answer: B. 12 volts

RMS = peak x 0.707 = 17 V x 0.707 = 12 V.

Tip: Peak to RMS: multiply by 0.707.

G5B10

What percentage of power loss is equivalent to a loss of 1 dB?

  1. A. 10.9 percent
  2. B. 12.2 percent
  3. C. 20.6 percent
  4. D. 25.9 percent
Show the answer and explanation

Answer: C. 20.6 percent

A 1 dB loss leaves 10^(-1/10) = 0.794 of the power, about 79.4 percent. The power lost is 100 - 79.4 = 20.6 percent.

Tip: 1 dB loss is about 20 percent gone.

G5B11

What is the ratio of PEP to average power for an unmodulated carrier?

  1. A. 0.707
  2. B. 1.00
  3. C. 1.414
  4. D. 2.00
Show the answer and explanation

Answer: B. 1.00

An unmodulated carrier has a constant amplitude, so its peak envelope power equals its average power. The ratio is 1 to 1, or 1.00.

Tip: Steady carrier: PEP = average.

G5B12

What is the RMS voltage across a 50-ohm dummy load dissipating 1200 watts?

  1. A. 173 volts
  2. B. 245 volts
  3. C. 346 volts
  4. D. 692 volts
Show the answer and explanation

Answer: B. 245 volts

Use E = square root of (P x R). E = square root of (1200 W x 50 ohms) = square root of 60,000 = 245 V RMS.

Tip: E = square root of P x R.

G5B13

What is the output PEP of an unmodulated carrier if the average power is 1060 watts?

  1. A. 530 watts
  2. B. 1060 watts
  3. C. 1500 watts
  4. D. 2120 watts
Show the answer and explanation

Answer: B. 1060 watts

An unmodulated carrier never changes amplitude, so PEP equals average power. PEP = 1060 W.

Tip: Plain carrier: PEP equals average power.

G5B14

What is the output PEP of 500 volts peak-to-peak across a 50-ohm load?

  1. A. 8.75 watts
  2. B. 625 watts
  3. C. 2500 watts
  4. D. 5000 watts
Show the answer and explanation

Answer: B. 625 watts

500 V peak-to-peak is 250 V peak. RMS = 250 x 0.707 = 176.8 V. PEP = E^2 / R = 176.8 x 176.8 / 50 = 31,250 / 50 = 625 W.

Tip: Halve P-P, x 0.707, square, divide by R.

G5C

Resistors, capacitors, and inductors in series and parallel; transformers

G5C01

What causes a voltage to appear across the secondary winding of a transformer when an AC voltage source is connected across its primary winding?

  1. A. Capacitive coupling
  2. B. Displacement current coupling
  3. C. Mutual inductance
  4. D. Mutual capacitance
Show the answer and explanation

Answer: C. Mutual inductance

The changing magnetic field from the primary winding passes through the secondary winding and induces a voltage there. This linking of the two coils by magnetism is called mutual inductance.

Tip: Transformers work by mutual inductance.

G5C02

What is the output voltage if an input signal is applied to the secondary winding of a 4:1 voltage step-down transformer instead of the primary winding?

  1. A. The input voltage is multiplied by 4
  2. B. The input voltage is divided by 4
  3. C. Additional resistance must be added in series with the primary to prevent overload
  4. D. Additional resistance must be added in parallel with the secondary to prevent overload
Show the answer and explanation

Answer: A. The input voltage is multiplied by 4

Feeding a 4:1 step-down transformer backwards makes it a 1:4 step-up transformer. The input voltage is multiplied by 4.

Tip: Backwards step-down = step-up.

G5C03

What is the total resistance of a 10-, a 20-, and a 50-ohm resistor connected in parallel?

  1. A. 5.9 ohms
  2. B. 0.17 ohms
  3. C. 17 ohms
  4. D. 80 ohms
Show the answer and explanation

Answer: A. 5.9 ohms

For parallel resistors, 1/R = 1/10 + 1/20 + 1/50 = 0.1 + 0.05 + 0.02 = 0.17. R = 1 / 0.17 = 5.9 ohms. Parallel total is always less than the smallest resistor.

Tip: Parallel total is below the smallest resistor.

G5C04

What is the approximate total resistance of a 100- and a 200-ohm resistor in parallel?

  1. A. 300 ohms
  2. B. 150 ohms
  3. C. 75 ohms
  4. D. 67 ohms
Show the answer and explanation

Answer: D. 67 ohms

For two parallel resistors, R = (R1 x R2) / (R1 + R2) = (100 x 200) / 300 = 20,000 / 300 = 67 ohms.

Tip: Two in parallel: product over sum.

G5C05

Why is the primary winding wire of a voltage step-up transformer usually a larger size than that of the secondary winding?

  1. A. To improve the coupling between the primary and secondary
  2. B. To accommodate the higher current of the primary
  3. C. To prevent parasitic oscillations due to resistive losses in the primary
  4. D. To ensure that the volume of the primary winding is equal to the volume of the secondary winding
Show the answer and explanation

Answer: B. To accommodate the higher current of the primary

A step-up transformer raises voltage but lowers current, so the primary carries more current than the secondary. Thicker wire on the primary handles that higher current.

Tip: Low voltage side = high current = thick wire.

G5C06

What is the voltage output of a transformer with a 500-turn primary and a 1500-turn secondary when 120 VAC is applied to the primary?

  1. A. 360 volts
  2. B. 120 volts
  3. C. 40 volts
  4. D. 25.5 volts
Show the answer and explanation

Answer: A. 360 volts

Voltage scales with the turns ratio: Es = Ep x (Ns / Np) = 120 V x (1500 / 500) = 120 x 3 = 360 V.

Tip: Voltage follows turns: 3 times turns, 3 times volts.

G5C07

What transformer turns ratio matches an antenna's 600-ohm feed point impedance to a 50-ohm coaxial cable?

  1. A. 3.5 to 1
  2. B. 12 to 1
  3. C. 24 to 1
  4. D. 144 to 1
Show the answer and explanation

Answer: A. 3.5 to 1

The turns ratio is the square root of the impedance ratio. Square root of (600 / 50) = square root of 12 = 3.46, about 3.5 to 1. 12 to 1 is the impedance ratio, not the turns ratio.

Tip: Turns ratio = square root of impedance ratio.

G5C08

What is the equivalent capacitance of two 5.0-nanofarad capacitors and one 750-picofarad capacitor connected in parallel?

  1. A. 576.9 nanofarads
  2. B. 1,733 picofarads
  3. C. 3,583 picofarads
  4. D. 10.750 nanofarads
Show the answer and explanation

Answer: D. 10.750 nanofarads

Capacitors in parallel simply add. 750 pF = 0.75 nF, so total = 5.0 + 5.0 + 0.75 = 10.75 nF.

Tip: Parallel capacitors add like series resistors.

G5C09

What is the capacitance of three 100-microfarad capacitors connected in series?

  1. A. 0.33 microfarads
  2. B. 3.0 microfarads
  3. C. 33.3 microfarads
  4. D. 300 microfarads
Show the answer and explanation

Answer: C. 33.3 microfarads

Equal capacitors in series: divide one value by how many there are. 100 uF / 3 = 33.3 uF. Series capacitance is always less than the smallest one.

Tip: Caps in series act like resistors in parallel.

G5C10

What is the inductance of three 10-millihenry inductors connected in parallel?

  1. A. 0.30 henries
  2. B. 3.3 henries
  3. C. 3.3 millihenries
  4. D. 30 millihenries
Show the answer and explanation

Answer: C. 3.3 millihenries

Equal inductors in parallel: divide one value by how many there are. 10 mH / 3 = 3.3 mH. Inductors combine just like resistors.

Tip: Inductors combine like resistors.

G5C11

What is the inductance of a circuit with a 20-millihenry inductor connected in series with a 50-millihenry inductor?

  1. A. 7 millihenries
  2. B. 14.3 millihenries
  3. C. 70 millihenries
  4. D. 1,000 millihenries
Show the answer and explanation

Answer: C. 70 millihenries

Inductors in series add, just like resistors. 20 mH + 50 mH = 70 mH.

Tip: Series inductors simply add.

G5C12

What is the capacitance of a 20-microfarad capacitor connected in series with a 50-microfarad capacitor?

  1. A. 0.07 microfarads
  2. B. 14.3 microfarads
  3. C. 70 microfarads
  4. D. 1,000 microfarads
Show the answer and explanation

Answer: B. 14.3 microfarads

Two capacitors in series use product over sum: C = (20 x 50) / (20 + 50) = 1000 / 70 = 14.3 uF.

Tip: Series caps: product over sum.

G5C13

Which of the following components should be added to a capacitor to increase the capacitance?

  1. A. An inductor in series
  2. B. An inductor in parallel
  3. C. A capacitor in parallel
  4. D. A capacitor in series
Show the answer and explanation

Answer: C. A capacitor in parallel

Capacitors in parallel add together, so adding another capacitor in parallel increases total capacitance. Adding one in series would decrease it.

Tip: More capacitance: add a cap in parallel.

G5C14

Which of the following components should be added to an inductor to increase the inductance?

  1. A. A capacitor in series
  2. B. A capacitor in parallel
  3. C. An inductor in parallel
  4. D. An inductor in series
Show the answer and explanation

Answer: D. An inductor in series

Inductors in series add together, so adding another inductor in series increases total inductance. Adding one in parallel would decrease it.

Tip: More inductance: add an inductor in series.

Practice G5 with scoring Take a 35-question practice exam