General › G3
G3 Radio Wave Propagation
37 questions in the pool. Your exam will include 3, one from each group below.
G3A
Sunspots and solar radiation; geomagnetic field and stability indices
G3A01
How does a higher sunspot number affect HF propagation?
- A. Higher sunspot numbers generally indicate a greater probability of good propagation at higher frequencies
- B. Lower sunspot numbers generally indicate greater probability of sporadic E propagation
- C. A zero sunspot number indicates that radio propagation is not possible on any band
- D. A zero sunspot number indicates undisturbed conditions
Show the answer and explanation
Answer: A. Higher sunspot numbers generally indicate a greater probability of good propagation at higher frequencies
More sunspots mean more solar ultraviolet radiation, which ionizes the upper atmosphere more strongly. A denser ionosphere can refract higher frequencies, so the upper HF bands open up more often.
Tip: More sunspots, higher bands open.
G3A02
What effect does a sudden ionospheric disturbance have on the daytime ionospheric propagation?
- A. It enhances propagation on all HF frequencies
- B. It disrupts signals on lower frequencies more than those on higher frequencies
- C. It disrupts communications via satellite more than direct communications
- D. None, because only areas on the night side of the Earth are affected
Show the answer and explanation
Answer: B. It disrupts signals on lower frequencies more than those on higher frequencies
A sudden ionospheric disturbance is caused by a burst of X-rays from a solar flare that greatly increases D region absorption on the sunlit side of Earth. Lower frequencies are absorbed the most, so they are disrupted more than higher frequencies.
Tip: SID: low bands hit hardest.
G3A03
Approximately how long does it take the increased ultraviolet and X-ray radiation from a solar flare to affect radio propagation on Earth?
- A. 28 days
- B. 1 to 2 hours
- C. 8 minutes
- D. 20 to 40 hours
Show the answer and explanation
Answer: C. 8 minutes
Ultraviolet and X-rays travel at the speed of light, and light from the Sun takes about 8 minutes to reach Earth. So a flare's radiation affects propagation about 8 minutes after it happens.
Tip: Light from the Sun: 8 minutes.
G3A04
Which of the following are the least reliable bands for long-distance communications during periods of low solar activity?
- A. 80 meters and 160 meters
- B. 60 meters and 40 meters
- C. 30 meters and 20 meters
- D. 15 meters, 12 meters, and 10 meters
Show the answer and explanation
Answer: D. 15 meters, 12 meters, and 10 meters
During low solar activity the ionosphere is too weak to refract the highest HF frequencies. That makes 15, 12, and 10 meters the least reliable for long-distance contacts, while the lower bands still work.
Tip: Low sunspots, high bands go quiet.
G3A05
What is the solar flux index?
- A. A measure of the highest frequency that is useful for ionospheric propagation between two points on Earth
- B. A count of sunspots that is adjusted for solar emissions
- C. Another name for the American sunspot number
- D. A measure of solar radiation with a wavelength of 10.7 centimeters
Show the answer and explanation
Answer: D. A measure of solar radiation with a wavelength of 10.7 centimeters
The solar flux index measures radio energy from the Sun at a wavelength of 10.7 centimeters (about 2800 MHz). It tracks solar activity and is not a sunspot count or a usable frequency.
Tip: Solar flux = 10.7 cm.
G3A06
What is a geomagnetic storm?
- A. A sudden drop in the solar flux index
- B. A thunderstorm that affects radio propagation
- C. Ripples in the geomagnetic force
- D. A temporary disturbance in Earth's geomagnetic field
Show the answer and explanation
Answer: D. A temporary disturbance in Earth's geomagnetic field
A geomagnetic storm is a temporary disturbance in Earth's magnetic field, usually caused by charged particles from the Sun. It is not a weather thunderstorm or a drop in solar flux.
Tip: Geomagnetic storm = Earth's field disturbed.
G3A07
At what point in the solar cycle does the 20-meter band usually support worldwide propagation during daylight hours?
- A. At the summer solstice
- B. Only at the maximum point
- C. Only at the minimum point
- D. At any point
Show the answer and explanation
Answer: D. At any point
20 meters is a reliable daytime DX band throughout the solar cycle. Even at solar minimum it usually supports worldwide daylight propagation.
Tip: 20 meters works any time in the cycle.
G3A08
How can a geomagnetic storm affect HF propagation?
- A. Improve high-latitude HF propagation
- B. Degrade ground wave propagation
- C. Improve ground wave propagation
- D. Degrade high-latitude HF propagation
Show the answer and explanation
Answer: D. Degrade high-latitude HF propagation
A geomagnetic storm disturbs the ionosphere most near the poles, where charged particles enter along Earth's magnetic field lines. That degrades HF signals that travel over high-latitude paths.
Tip: Storms hurt polar HF paths.
G3A09
How can high geomagnetic activity benefit radio communications?
- A. Creates auroras that can reflect VHF signals
- B. Increases signal strength for HF signals passing through the polar regions
- C. Improve HF long path propagation
- D. Reduce long delayed echoes
Show the answer and explanation
Answer: A. Creates auroras that can reflect VHF signals
High geomagnetic activity can create auroras, and the ionized aurora can reflect VHF signals. Hams use this aurora mode for contacts that would not otherwise be possible.
Tip: Aurora reflects VHF.
G3A10
What causes HF propagation conditions to vary periodically in a 26- to 28-day cycle?
- A. Long term oscillations in the upper atmosphere
- B. Cyclic variation in Earth's radiation belts
- C. Rotation of the Sun's surface layers around its axis
- D. The position of the Moon in its orbit
Show the answer and explanation
Answer: C. Rotation of the Sun's surface layers around its axis
The Sun rotates about once every 27 days, so active regions face Earth again on a roughly 26- to 28-day cycle. That causes propagation conditions to repeat on that schedule.
Tip: Sun spins about every 27 days.
G3A11
How long does it take a coronal mass ejection to affect radio propagation on Earth?
- A. 28 days
- B. 14 days
- C. 4 to 8 minutes
- D. 15 hours to several days
Show the answer and explanation
Answer: D. 15 hours to several days
A coronal mass ejection is a cloud of charged particles, which travel much slower than light. They take about 15 hours to several days to reach Earth and disturb propagation.
Tip: CME particles arrive in hours to days.
G3A12
What does the K-index measure?
- A. The relative position of sunspots on the surface of the Sun
- B. The short-term stability of Earth's geomagnetic field
- C. The short-term stability of the Sun's magnetic field
- D. The solar radio flux at Boulder, Colorado
Show the answer and explanation
Answer: B. The short-term stability of Earth's geomagnetic field
The K-index measures the short-term stability of Earth's geomagnetic field, updated every 3 hours. It measures Earth's field, not the Sun's.
Tip: K-index = Kurrent (short-term) Earth field.
G3A13
What does the A-index measure?
- A. The relative position of sunspots on the surface of the Sun
- B. The amount of polarization of the Sun's electric field
- C. The long-term stability of Earth's geomagnetic field
- D. The solar radio flux at Boulder, Colorado
Show the answer and explanation
Answer: C. The long-term stability of Earth's geomagnetic field
The A-index measures the long-term (daily average) stability of Earth's geomagnetic field. A low A-index means a quiet, stable field.
Tip: A-index = Average, long-term.
G3A14
How is long distance radio communication usually affected by the charged particles that reach Earth from solar coronal holes?
- A. HF communication is improved
- B. HF communication is disturbed
- C. VHF/UHF ducting is improved
- D. VHF/UHF ducting is disturbed
Show the answer and explanation
Answer: B. HF communication is disturbed
Coronal holes release streams of charged particles that disturb Earth's geomagnetic field and ionosphere. This disturbs HF communication rather than improving it.
Tip: Coronal hole particles disturb HF.
G3B
Maximum Usable Frequency; Lowest Usable Frequency; short path and long path propagation; determining propagation conditions; ionospheric refraction
G3B01
What is a characteristic of skywave signals arriving at your location by both short-path and long-path propagation?
- A. Periodic fading approximately every 10 seconds
- B. Signal strength increased by 3 dB
- C. The signal might be cancelled causing severe attenuation
- D. A slightly delayed echo might be heard
Show the answer and explanation
Answer: D. A slightly delayed echo might be heard
A long-path signal travels the long way around the Earth, so it arrives a little later than the short-path signal. The result is a slight echo on the received signal.
Tip: Two paths, slight echo.
G3B02
What factors affect the MUF?
- A. Path distance and location
- B. Time of day and season
- C. Solar radiation and ionospheric disturbances
- D. All these choices are correct
Show the answer and explanation
Answer: D. All these choices are correct
The MUF depends on the path distance and location, time of day and season, and solar radiation and ionospheric disturbances. All of these change how strongly the ionosphere is ionized.
Tip: MUF depends on everything.
G3B03
Which frequency will have the least attenuation for long-distance skip propagation?
- A. Just below the MUF
- B. Just above the LUF
- C. Just below the critical frequency
- D. Just above the critical frequency
Show the answer and explanation
Answer: A. Just below the MUF
Absorption in the ionosphere is lower at higher frequencies, so the highest frequency that still gets refracted back works best. Just below the MUF gives the least attenuation for long-distance skip.
Tip: Just below the MUF is best.
G3B04
Which of the following is a way to determine current propagation on a desired band from your station?
- A. Use a network of automated receiving stations on the internet to see where your transmissions are being received
- B. Check the A-index
- C. Send a series of dots and listen for echoes
- D. All these choices are correct
Show the answer and explanation
Answer: A. Use a network of automated receiving stations on the internet to see where your transmissions are being received
Automated receiving networks on the internet, such as reverse beacon networks, report where your signal is being heard. This shows actual propagation from your station on that band.
Tip: Let the internet hear you.
G3B05
How does the ionosphere affect radio waves with frequencies below the MUF and above the LUF?
- A. They are refracted back to Earth
- B. They pass through the ionosphere
- C. They are amplified by interaction with the ionosphere
- D. They are refracted and trapped in the ionosphere to circle Earth
Show the answer and explanation
Answer: A. They are refracted back to Earth
Frequencies between the LUF and the MUF are refracted back to Earth by the ionosphere. Above the MUF they pass through, and below the LUF they are absorbed.
Tip: Between LUF and MUF, signals come back.
G3B06
What usually happens to radio waves with frequencies below the LUF?
- A. They are refracted back to Earth
- B. They pass through the ionosphere
- C. They are attenuated before reaching the destination
- D. They are refracted and trapped in the ionosphere to circle Earth
Show the answer and explanation
Answer: C. They are attenuated before reaching the destination
Below the LUF, signals are absorbed by the ionosphere, mainly the D region, before they reach the destination. They are too weak to be useful.
Tip: Below LUF, absorbed.
G3B07
What does LUF stand for?
- A. The Lowest Usable Frequency for communications between two specific points
- B. The Lowest Usable Frequency for communications to any point outside a 100-mile radius
- C. The Lowest Usable Frequency during a 24-hour period
- D. The Lowest Usable Frequency during the past 60 minutes
Show the answer and explanation
Answer: A. The Lowest Usable Frequency for communications between two specific points
LUF stands for Lowest Usable Frequency for communications between two specific points. Below it, absorption makes the path unusable.
Tip: LUF = Lowest Usable Frequency.
G3B08
What does MUF stand for?
- A. The Minimum Usable Frequency for communications between two points
- B. The Maximum Usable Frequency for communications between two points
- C. The Minimum Usable Frequency during a 24-hour period
- D. The Maximum Usable Frequency during a 24-hour period
Show the answer and explanation
Answer: B. The Maximum Usable Frequency for communications between two points
MUF stands for Maximum Usable Frequency for communications between two points. Above it, signals pass through the ionosphere instead of returning to Earth.
Tip: MUF = Maximum Usable Frequency.
G3B09
What is the approximate maximum distance along the Earth's surface normally covered in one hop using the F2 region?
- A. 180 miles
- B. 1,200 miles
- C. 2,500 miles
- D. 12,000 miles
Show the answer and explanation
Answer: C. 2,500 miles
The F2 region is the highest ionospheric layer, so one hop through it covers the longest distance, about 2,500 miles. The lower E region gives about 1,200 miles per hop.
Tip: F2 hop: about 2,500 miles.
G3B10
What is the approximate maximum distance along the Earth's surface normally covered in one hop using the E region?
- A. 180 miles
- B. 1,200 miles
- C. 2,500 miles
- D. 12,000 miles
Show the answer and explanation
Answer: B. 1,200 miles
The E region is lower than the F2 region, so a single hop covers less ground, about 1,200 miles. The F2 region reaches about 2,500 miles.
Tip: E hop: about 1,200 miles.
G3B11
What happens to HF propagation when the LUF exceeds the MUF?
- A. Propagation via ordinary skywave communications is not possible over that path
- B. HF communications over the path are enhanced
- C. Double-hop propagation along the path is more common
- D. Propagation over the path on all HF frequencies is enhanced
Show the answer and explanation
Answer: A. Propagation via ordinary skywave communications is not possible over that path
If the lowest usable frequency is higher than the maximum usable frequency, there is no frequency that works on that path. Ordinary skywave communication is not possible.
Tip: LUF above MUF: no window.
G3B12
Which of the following is typical of the lower HF frequencies during the summer?
- A. Poor propagation at any time of day
- B. World-wide propagation during daylight hours
- C. Heavy distortion on signals due to photon absorption
- D. High levels of atmospheric noise or static
Show the answer and explanation
Answer: D. High levels of atmospheric noise or static
Summer thunderstorms create lots of static, which is strongest on the lower HF bands. That makes high atmospheric noise typical on those bands in summer.
Tip: Summer low bands = static crashes.
G3C
Ionospheric regions; critical angle and frequency; HF scatter; near vertical incidence skywave (NVIS)
G3C01
Which ionospheric region is closest to the surface of Earth?
- A. The D region
- B. The E region
- C. The F1 region
- D. The F2 region
Show the answer and explanation
Answer: A. The D region
The D region is the lowest ionospheric layer, closest to Earth's surface. Above it are the E, F1, and F2 regions.
Tip: D is down low.
G3C02
What is meant by the term “critical frequency” at a given incidence angle?
- A. The highest frequency which is refracted back to Earth
- B. The lowest frequency which is refracted back to Earth
- C. The frequency at which the signal-to-noise ratio approaches unity
- D. The frequency at which the signal-to-noise ratio is 6 dB
Show the answer and explanation
Answer: A. The highest frequency which is refracted back to Earth
The critical frequency is the highest frequency that is refracted back to Earth at a given incidence angle. Higher frequencies pass through the ionosphere into space.
Tip: Critical frequency = highest that returns.
G3C03
Why is skip propagation via the F2 region longer than that via the other ionospheric regions?
- A. Because it is the densest
- B. Because of the Doppler effect
- C. Because it is the highest
- D. Because of temperature inversions
Show the answer and explanation
Answer: C. Because it is the highest
The F2 region is the highest ionospheric layer, so signals refracted there come down farther away. Higher refraction point means longer skip distance.
Tip: Highest layer, longest skip.
G3C04
What does the term “critical angle” mean, as applied to radio wave propagation?
- A. The long path azimuth of a distant station
- B. The short path azimuth of a distant station
- C. The lowest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions
- D. The highest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions
Show the answer and explanation
Answer: D. The highest takeoff angle that will return a radio wave to Earth under specific ionospheric conditions
The critical angle is the highest takeoff angle that still returns a radio wave to Earth under given conditions. Signals sent more steeply than that pass through the ionosphere.
Tip: Critical angle = steepest that returns.
G3C05
Why is long-distance communication on the 40-, 60-, 80-, and 160-meter bands more difficult during the day?
- A. The F region absorbs signals at these frequencies during daylight hours
- B. The F region is unstable during daylight hours
- C. The D region absorbs signals at these frequencies during daylight hours
- D. The E region is unstable during daylight hours
Show the answer and explanation
Answer: C. The D region absorbs signals at these frequencies during daylight hours
During daylight the D region forms and absorbs signals at lower frequencies like 40, 60, 80, and 160 meters. It disappears at night, which is why these bands open up for distance after dark.
Tip: Daytime D region absorbs low bands.
G3C06
What is a characteristic of HF scatter?
- A. Phone signals have high intelligibility
- B. Signals have a fluttering sound
- C. There are very large, sudden swings in signal strength
- D. Scatter propagation occurs only at night
Show the answer and explanation
Answer: B. Signals have a fluttering sound
Scatter signals arrive by many different paths at once, so they have a fluttering sound. They are usually weak and hard to understand, not highly intelligible.
Tip: Scatter flutters.
G3C07
What makes HF scatter signals often sound distorted?
- A. The ionospheric region involved is unstable
- B. Ground waves are absorbing much of the signal
- C. The E region is not present
- D. Energy is scattered into the skip zone through several different paths
Show the answer and explanation
Answer: D. Energy is scattered into the skip zone through several different paths
Scatter energy reaches the skip zone through several different paths of different lengths. The slightly different arrival times blend together and make the signal sound distorted.
Tip: Many paths, distorted sound.
G3C08
Why are HF scatter signals in the skip zone usually weak?
- A. Only a small part of the signal energy is scattered into the skip zone
- B. Signals are scattered from the magnetosphere, which is not a good reflector
- C. Propagation is via ground waves, which absorb most of the signal energy
- D. Propagation is via ducts in the F region, which absorb most of the energy
Show the answer and explanation
Answer: A. Only a small part of the signal energy is scattered into the skip zone
Only a small part of the transmitted energy is scattered into the skip zone. Most of it goes on to the normal skip area, so scatter signals are weak.
Tip: Only a little energy scatters.
G3C09
What type of propagation allows signals to be heard in the transmitting station's skip zone?
- A. Faraday rotation
- B. Scatter
- C. Chordal hop
- D. Short-path
Show the answer and explanation
Answer: B. Scatter
Scatter propagation sends a small amount of energy into the skip zone, where neither ground wave nor normal skywave reaches. That lets stations in the skip zone hear the signal.
Tip: Skip zone heard by scatter.
G3C10
What is near vertical incidence skywave (NVIS) propagation?
- A. Propagation near the MUF
- B. Short distance MF or HF propagation at high elevation angles
- C. Long path HF propagation at sunrise and sunset
- D. Double hop propagation near the LUF
Show the answer and explanation
Answer: B. Short distance MF or HF propagation at high elevation angles
NVIS sends MF or HF signals nearly straight up at high elevation angles so they come back down close by. It provides short-distance coverage, for example a few hundred miles, with no skip zone.
Tip: NVIS: straight up, nearby down.
G3C11
Which ionospheric region is the most absorbent of signals below 10 MHz during daylight hours?
- A. The F2 region
- B. The F1 region
- C. The E region
- D. The D region
Show the answer and explanation
Answer: D. The D region
The D region is the most absorbent layer for signals below 10 MHz during daylight. It fades away at night, letting low-band signals travel farther.
Tip: D region absorbs by Day.