Ham Tech Prep

General › G2

G2 Operating Procedures

60 questions in the pool. Your exam will include 5, one from each group below.

Practice G2 now

G2A

Phone operating procedures: USB/LSB conventions, breaking into a contact, transmitter setup for voice operation; answering DX stations

G2A01

Which mode is most commonly used for voice communications on frequencies of 14 MHz or higher?

  1. A. Upper sideband
  2. B. Lower sideband
  3. C. Suppressed sideband
  4. D. Double sideband
Show the answer and explanation

Answer: A. Upper sideband

By convention, amateurs use upper sideband for voice on 14 MHz (20 meters) and higher. Lower sideband is used on bands below 10 MHz.

Tip: Above 10 MHz, think Upper.

G2A02

Which mode is most commonly used for voice communications on the 160-, 75-, and 40-meter bands?

  1. A. Upper sideband
  2. B. Lower sideband
  3. C. Suppressed sideband
  4. D. Double sideband
Show the answer and explanation

Answer: B. Lower sideband

By common practice, voice on 160, 75 and 40 meters uses lower sideband. These are all below 10 MHz, where LSB is the convention.

Tip: Below 10 MHz, think Lower.

G2A03

Which mode is most commonly used for SSB voice communications in the VHF and UHF bands?

  1. A. Upper sideband
  2. B. Lower sideband
  3. C. Suppressed sideband
  4. D. Double sideband
Show the answer and explanation

Answer: A. Upper sideband

SSB voice on VHF and UHF uses upper sideband by convention. The 'upper above 10 MHz' rule continues all the way up.

Tip: VHF/UHF SSB: Upper.

G2A04

Which mode is most commonly used for voice communications on the 17- and 12-meter bands?

  1. A. Upper sideband
  2. B. Lower sideband
  3. C. Suppressed sideband
  4. D. Double sideband
Show the answer and explanation

Answer: A. Upper sideband

17 meters (18 MHz) and 12 meters (24 MHz) are above 10 MHz, so voice uses upper sideband. 60 meters is the only band below 10 MHz that also uses USB.

Tip: 17m and 12m: above 10 MHz, so USB.

G2A05

Which mode of voice communication is most commonly used on the HF amateur bands?

  1. A. Frequency modulation
  2. B. Double sideband
  3. C. Single sideband
  4. D. Single phase modulation
Show the answer and explanation

Answer: C. Single sideband

Single sideband is the most common voice mode on HF because it is narrow and efficient. FM and AM are used much less on HF.

Tip: HF voice = SSB.

G2A06

Which of the following is an advantage of using single sideband, as compared to other analog voice modes on the HF amateur bands?

  1. A. Very high-fidelity voice modulation
  2. B. Less subject to interference from atmospheric static crashes
  3. C. Ease of tuning on receive and immunity to impulse noise
  4. D. Less bandwidth used and greater power efficiency
Show the answer and explanation

Answer: D. Less bandwidth used and greater power efficiency

SSB uses less bandwidth than AM and puts all its power into one sideband with no carrier, making it more power efficient. It is not high fidelity or immune to noise.

Tip: SSB: narrow and efficient.

G2A07

Which of the following statements is true of single sideband (SSB)?

  1. A. Only one sideband and the carrier are transmitted; the other sideband is suppressed
  2. B. Only one sideband is transmitted; the other sideband and carrier are suppressed
  3. C. SSB is the only voice mode authorized on the 20-, 15-, and 10-meter amateur bands
  4. D. SSB is the only voice mode authorized on the 160-, 75-, and 40-meter amateur bands
Show the answer and explanation

Answer: B. Only one sideband is transmitted; the other sideband and carrier are suppressed

In SSB, the carrier and one sideband are suppressed, leaving only one sideband. That is why it is efficient; other voice modes such as AM are also legal on HF.

Tip: SSB: one sideband, no carrier.

G2A08

What is the recommended way to break into a phone contact?

  1. A. Say “QRZ” several times, followed by your call sign
  2. B. Say your call sign once
  3. C. Say “Breaker Breaker”
  4. D. Say “CQ” followed by the call sign of either station
Show the answer and explanation

Answer: B. Say your call sign once

To break into a phone contact, simply say your call sign once during a pause. Saying 'Breaker' is CB style, and CQ or QRZ are for different purposes.

Tip: Just say your call once.

G2A09

Why do most amateur stations use lower sideband on the 160-, 75-, and 40-meter bands?

  1. A. Lower sideband is more efficient than upper sideband at these frequencies
  2. B. Lower sideband is the only sideband legal on these frequency bands
  3. C. Because it is fully compatible with an AM detector
  4. D. It is commonly accepted amateur practice
Show the answer and explanation

Answer: D. It is commonly accepted amateur practice

There is no rule requiring LSB below 10 MHz; it is simply commonly accepted amateur practice. Using the same sideband as everyone else makes tuning easy.

Tip: LSB down low is custom, not law.

G2A10

Which of the following statements is true of VOX operation versus PTT operation?

  1. A. The received signal is more natural sounding
  2. B. It allows “hands free” operation
  3. C. It occupies less bandwidth
  4. D. It provides more power output
Show the answer and explanation

Answer: B. It allows “hands free” operation

VOX (voice operated transmit) keys the transmitter when you speak, giving hands-free operation. It does not change bandwidth or power.

Tip: VOX = voice keys the rig, hands free.

G2A11

Generally, who should respond to a station in the contiguous 48 states calling “CQ DX”?

  1. A. Any caller is welcome to respond
  2. B. Only stations in Germany
  3. C. Any stations outside the lower 48 states
  4. D. Only contest stations
Show the answer and explanation

Answer: C. Any stations outside the lower 48 states

A station in the lower 48 states calling CQ DX wants contacts with distant stations, so only stations outside the lower 48 should answer. DX means distance.

Tip: CQ DX: answer only if you're far away.

G2A12

What control is typically adjusted for proper ALC setting on a single sideband transceiver?

  1. A. RF clipping level
  2. B. Transmit audio or microphone gain
  3. C. Antenna inductance or capacitance
  4. D. Attenuator level
Show the answer and explanation

Answer: B. Transmit audio or microphone gain

ALC on an SSB rig is set mainly by adjusting the transmit audio or microphone gain. Too much mic gain drives the ALC hard and causes distortion.

Tip: Set ALC with mic gain.

G2B

Operating effectively; band plans; drills and emergencies; RACES operation

G2B01

Which of the following is true concerning access to frequencies?

  1. A. Nets have priority
  2. B. QSOs in progress have priority
  3. C. Except during emergencies, no amateur station has priority access to any frequency
  4. D. Contest operations should yield to non-contest use of frequencies
Show the answer and explanation

Answer: C. Except during emergencies, no amateur station has priority access to any frequency

Except during emergencies, no amateur station has priority access to any frequency. Nets and ongoing QSOs get courtesy, not legal priority.

Tip: No one owns a frequency.

FCC rule reference: Part 97.101(b), (c)

G2B02

What is the first thing you should do if you are communicating with another amateur station and hear a station in distress break in?

  1. A. Inform your local emergency coordinator
  2. B. Acknowledge the station in distress and determine what assistance may be needed
  3. C. Immediately decrease power to avoid interfering with the station in distress
  4. D. Immediately cease all transmissions
Show the answer and explanation

Answer: B. Acknowledge the station in distress and determine what assistance may be needed

If a station in distress breaks in, first acknowledge it and find out what help is needed. Distress traffic takes priority over everything else.

Tip: Distress call: acknowledge and help.

G2B03

What is good amateur practice if propagation changes during a contact creating interference from other stations using the frequency?

  1. A. Advise the interfering stations that you are on the frequency and that you have priority
  2. B. Decrease power and continue to transmit
  3. C. Attempt to resolve the interference problem with the other stations in a mutually acceptable manner
  4. D. Switch to the opposite sideband
Show the answer and explanation

Answer: C. Attempt to resolve the interference problem with the other stations in a mutually acceptable manner

When propagation changes cause interference, good practice is to work it out with the other stations in a mutually acceptable way. No one has priority on a frequency.

Tip: Interference? Work it out politely.

G2B04

When selecting a CW transmitting frequency, what minimum separation from other stations should be used to minimize interference to stations on adjacent frequencies?

  1. A. 5 Hz to 50 Hz
  2. B. 150 Hz to 500 Hz
  3. C. 1 kHz to 3 kHz
  4. D. 3 kHz to 6 kHz
Show the answer and explanation

Answer: B. 150 Hz to 500 Hz

CW signals are narrow, so 150 to 500 Hz of separation is enough to avoid interfering with adjacent stations. Wider spacing is needed for SSB.

Tip: CW spacing: a few hundred hertz.

G2B05

When selecting an SSB transmitting frequency, what minimum separation should be used to minimize interference to stations on adjacent frequencies?

  1. A. 5 Hz to 50 Hz
  2. B. 150 Hz to 500 Hz
  3. C. 2 kHz to 3 kHz
  4. D. Approximately 6 kHz
Show the answer and explanation

Answer: C. 2 kHz to 3 kHz

An SSB voice signal is about 2.4 to 3 kHz wide, so leave at least 2 to 3 kHz of separation from adjacent stations.

Tip: SSB spacing: 2 to 3 kHz.

G2B06

How can you avoid harmful interference on an apparently clear frequency before calling CQ on CW or phone?

  1. A. Send “QRL?” on CW, followed by your call sign; or, if using phone, ask if the frequency is in use, followed by your call sign
  2. B. Listen for 2 minutes before calling CQ
  3. C. Send the letter “V” in Morse code several times and listen for a response, or say “test” several times and listen for a response
  4. D. Send “QSY” on CW or if using phone, announce “the frequency is in use,” then give your call sign and listen for a response
Show the answer and explanation

Answer: A. Send “QRL?” on CW, followed by your call sign; or, if using phone, ask if the frequency is in use, followed by your call sign

Before calling CQ, send 'QRL?' and your call sign on CW, or ask 'Is this frequency in use?' and give your call on phone. Then listen for a reply.

Tip: QRL? means 'Is this frequency in use?'

G2B07

Which of the following complies with commonly accepted amateur practice when choosing a frequency on which to initiate a call?

  1. A. Listen on the frequency for at least two minutes to be sure it is clear
  2. B. Identify your station by transmitting your call sign at least 3 times
  3. C. Follow the voluntary band plan
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. Follow the voluntary band plan

Following the voluntary band plan is commonly accepted practice when picking a frequency. There is no 2-minute listening rule, and you do not need to send your call 3 times.

Tip: Follow the band plan.

G2B08

What is the voluntary band plan restriction for US stations transmitting within the 48 contiguous states in the 50.1 MHz to 50.125 MHz band segment?

  1. A. Only contacts with stations not within the 48 contiguous states
  2. B. Only contacts with other stations within the 48 contiguous states
  3. C. Only digital contacts
  4. D. Only SSTV contacts
Show the answer and explanation

Answer: A. Only contacts with stations not within the 48 contiguous states

The band plan reserves 50.100 to 50.125 MHz as a DX window, so stations in the lower 48 should only use it to contact stations outside the 48 contiguous states.

Tip: 50.100 to 50.125: 6m DX window.

G2B09

Who may be the control operator of an amateur station transmitting in RACES to assist relief operations during a disaster?

  1. A. Only a person holding an FCC-issued amateur operator license
  2. B. Only a RACES net control operator
  3. C. A person holding an FCC-issued amateur operator license or an appropriate government official
  4. D. Any control operator when normal communication systems are operational
Show the answer and explanation

Answer: A. Only a person holding an FCC-issued amateur operator license

Only a person holding an FCC-issued amateur operator license may be the control operator of a RACES station. Government officials without an amateur license cannot.

Tip: RACES control op needs an amateur license.

FCC rule reference: Part 97.407(a)

G2B10

Which of the following is good amateur practice for net management?

  1. A. Always use multiple sets of phonetics during check-in
  2. B. Have a backup frequency in case of interference or poor conditions
  3. C. Transmit the full net roster at the beginning of every session
  4. D. All these choices are correct
Show the answer and explanation

Answer: B. Have a backup frequency in case of interference or poor conditions

Having a backup frequency is good net practice in case of interference or poor conditions. Multiple phonetics and reading the full roster just waste time.

Tip: Nets: always have a backup frequency.

G2B11

How often may RACES training drills and tests be routinely conducted without special authorization?

  1. A. No more than 1 hour per month
  2. B. No more than 2 hours per month
  3. C. No more than 1 hour per week
  4. D. No more than 2 hours per week
Show the answer and explanation

Answer: C. No more than 1 hour per week

RACES training drills and tests may be held up to 1 hour per week without special authorization. Longer drills need FCC permission.

Tip: RACES drills: 1 hour a week.

FCC rule reference: Part 97.407(d)(4)

G2C

CW operating procedures and procedural signals; Q signals; full break-in

G2C01

Which of the following describes full break-in CW operation (QSK)?

  1. A. Breaking stations send the Morse code prosign “BK”
  2. B. Automatic keyers, instead of hand keys, are used to send Morse code
  3. C. An operator must activate a manual send/receive switch before and after every transmission
  4. D. Transmitting stations can receive between code characters and elements
Show the answer and explanation

Answer: D. Transmitting stations can receive between code characters and elements

With full break-in (QSK), the receiver works between the dots and dashes, so you can hear other stations while sending. Anyone can interrupt you instantly.

Tip: QSK: listen between your own dits.

G2C02

What should you do if a CW station sends “QRS?”

  1. A. Send slower
  2. B. Change frequency
  3. C. Increase your power
  4. D. Repeat everything twice
Show the answer and explanation

Answer: A. Send slower

QRS means 'send more slowly.' QRS? asks whether you should send slower, so you should slow down.

Tip: QRS = slow down.

G2C03

What does it mean when a CW operator sends “KN” at the end of a transmission?

  1. A. No US stations should call
  2. B. Operating full break-in
  3. C. Listening only for a specific station or stations
  4. D. Closing station now
Show the answer and explanation

Answer: C. Listening only for a specific station or stations

KN means 'go ahead, only the station I'm in contact with.' Other stations should not call. Plain K invites anyone.

Tip: KN: named station only.

G2C04

What does the Q signal “QRL?” mean?

  1. A. “Will you keep the frequency clear?”
  2. B. “Are you operating full break-in?” or “Can you operate full break-in?”
  3. C. “Are you listening only for a specific station?”
  4. D. “Are you busy?” or “Is this frequency in use?”
Show the answer and explanation

Answer: D. “Are you busy?” or “Is this frequency in use?”

QRL? asks 'Are you busy?' or 'Is this frequency in use?' Send it before calling CQ on a frequency that seems clear.

Tip: QRL? = Is this frequency busy?

G2C05

What is the best speed to use when answering a CQ in Morse code?

  1. A. The fastest speed at which you are comfortable copying, but no slower than the CQ
  2. B. The fastest speed at which you are comfortable copying, but no faster than the CQ
  3. C. At the standard calling speed of 10 wpm
  4. D. At the standard calling speed of 5 wpm
Show the answer and explanation

Answer: B. The fastest speed at which you are comfortable copying, but no faster than the CQ

Answer a CQ at a speed you can comfortably copy, but no faster than the calling station. Sending faster than they did may mean they cannot copy you.

Tip: Never answer faster than the CQ.

G2C06

What does the term “zero beat” mean in CW operation?

  1. A. Matching the speed of the transmitting station
  2. B. Operating split to avoid interference on frequency
  3. C. Sending without error
  4. D. Matching the transmit frequency to the frequency of a received signal
Show the answer and explanation

Answer: D. Matching the transmit frequency to the frequency of a received signal

Zero beat means matching your transmit frequency to the received station's frequency. Then both stations are on exactly the same frequency.

Tip: Zero beat: same frequency.

G2C07

When sending CW, what does a “C” mean when added to the RST report?

  1. A. Chirpy or unstable signal
  2. B. Report was read from an S meter rather than estimated
  3. C. 100 percent copy
  4. D. Key clicks
Show the answer and explanation

Answer: A. Chirpy or unstable signal

A 'C' added to an RST report means the signal is chirpy or unstable. For example, 579C means a good signal with chirp.

Tip: C = chirp.

G2C08

What prosign is sent to indicate the end of a formal message when using CW?

  1. A. SK
  2. B. BK
  3. C. AR
  4. D. KN
Show the answer and explanation

Answer: C. AR

AR is the CW prosign that marks the end of a formal message. SK ends the whole contact, and KN or BK are turnover signals.

Tip: AR = all read, end of message.

G2C09

What does the Q signal “QSL” mean?

  1. A. Send slower
  2. B. We have already confirmed the contact
  3. C. I have received and understood
  4. D. We have worked before
Show the answer and explanation

Answer: C. I have received and understood

QSL means 'I have received and understood' (an acknowledgment). That is also why confirmation postcards are called QSL cards.

Tip: QSL = got it.

G2C10

What does the Q signal “QRN” mean?

  1. A. Send more slowly
  2. B. Stop sending
  3. C. Zero beat my signal
  4. D. I am troubled by static
Show the answer and explanation

Answer: D. I am troubled by static

QRN means 'I am troubled by static,' meaning natural noise like lightning crashes. QRM is man-made interference.

Tip: QRN = Natural noise.

G2C11

What does the Q signal “QRV” mean?

  1. A. You are sending too fast
  2. B. There is interference on the frequency
  3. C. I am quitting for the day
  4. D. I am ready to receive
Show the answer and explanation

Answer: D. I am ready to receive

QRV means 'I am ready to receive' or ready to operate. QRS is send slower and QRT is stop sending.

Tip: QRV = ready.

G2D

Volunteer Monitor Program; HF operations

G2D01

What is the Volunteer Monitor Program?

  1. A. Amateur volunteers who are formally enlisted to monitor the airwaves for rules violations
  2. B. Amateur volunteers who conduct amateur licensing examinations
  3. C. Amateur volunteers who conduct frequency coordination for amateur VHF repeaters
  4. D. Amateur volunteers who use their station equipment to help civil defense organizations in times of emergency
Show the answer and explanation

Answer: A. Amateur volunteers who are formally enlisted to monitor the airwaves for rules violations

The Volunteer Monitor Program uses amateur volunteers formally enlisted to monitor the bands for rules violations. They help the FCC by reporting and educating, not by enforcing.

Tip: Volunteer Monitors watch for rule breaking.

G2D02

Which of the following are objectives of the Volunteer Monitor Program?

  1. A. To conduct efficient and orderly amateur licensing examinations
  2. B. To provide emergency and public safety communications
  3. C. To coordinate repeaters for efficient and orderly spectrum usage
  4. D. To encourage amateur radio operators to self-regulate and comply with the rules
Show the answer and explanation

Answer: D. To encourage amateur radio operators to self-regulate and comply with the rules

The program's goal is to encourage amateurs to self-regulate and follow the rules. It is not about exams, repeater coordination or emergency service.

Tip: Goal: hams policing themselves.

G2D03

What procedure may be used by Volunteer Monitors to localize a station whose continuous carrier is holding a repeater on in their area?

  1. A. Compare vertical and horizontal signal strengths on the input frequency
  2. B. Compare beam headings on the repeater input from their home locations with that of other Volunteer Monitors
  3. C. Compare signal strengths between the input and output of the repeater
  4. D. All these choices are correct
Show the answer and explanation

Answer: B. Compare beam headings on the repeater input from their home locations with that of other Volunteer Monitors

Volunteer Monitors at different locations compare beam headings on the repeater input frequency. Where their bearings cross is where the interfering station is.

Tip: Crossing beam headings pinpoint the station.

G2D04

Which of the following describes an azimuthal projection map?

  1. A. A map that shows accurate land masses
  2. B. A map that shows true bearings and distances from a specific location
  3. C. A map that shows the angle at which an amateur satellite crosses the equator
  4. D. A map that shows the number of degrees longitude that an amateur satellite appears to move westward at the equator with each orbit
Show the answer and explanation

Answer: B. A map that shows true bearings and distances from a specific location

An azimuthal projection map is centered on one location and shows true bearings and distances from it. Hams use it to aim beam antennas.

Tip: Azimuthal map: point your beam.

G2D05

Which of the following indicates that you are looking for an HF contact with any station?

  1. A. Sign your call sign once, followed by the words “listening for a call” -- if no answer, change frequency and repeat
  2. B. Say “QTC” followed by “this is” and your call sign -- if no answer, change frequency and repeat
  3. C. Repeat “CQ” a few times, followed by “this is,” then your call sign a few times, then pause to listen, repeat as necessary
  4. D. Transmit an unmodulated carried for approximately 10 seconds, followed by “this is” and your call sign, and pause to listen -- repeat as necessary
Show the answer and explanation

Answer: C. Repeat “CQ” a few times, followed by “this is,” then your call sign a few times, then pause to listen, repeat as necessary

To ask for a contact with any station, call 'CQ' a few times, say 'this is' and your call sign a few times, then listen. Repeat if needed.

Tip: CQ = calling any station.

G2D06

How is a directional antenna pointed when making a “long-path” contact with another station?

  1. A. Toward the rising sun
  2. B. Along the gray line
  3. C. 180 degrees from the station's short-path heading
  4. D. Toward the north
Show the answer and explanation

Answer: C. 180 degrees from the station's short-path heading

For a long-path contact, aim the antenna 180 degrees from the short-path heading. The signal goes the long way around the Earth.

Tip: Long path: turn the beam around.

G2D07

Which of the following are examples of the NATO Phonetic Alphabet?

  1. A. Able, Baker, Charlie, Dog
  2. B. Adam, Boy, Charles, David
  3. C. America, Boston, Canada, Denmark
  4. D. Alpha, Bravo, Charlie, Delta
Show the answer and explanation

Answer: D. Alpha, Bravo, Charlie, Delta

Alpha, Bravo, Charlie, Delta are from the NATO (ITU) phonetic alphabet. Able, Baker and the others are older or non-standard alphabets.

Tip: Alpha Bravo Charlie = NATO.

G2D08

Why do many amateurs keep a station log?

  1. A. The FCC requires a log of all international contacts
  2. B. The FCC requires a log of all international third-party traffic
  3. C. The log provides evidence of operation needed to renew a license without retest
  4. D. To help with a reply if the FCC requests information about your station
Show the answer and explanation

Answer: D. To help with a reply if the FCC requests information about your station

Logs are not required by the FCC for most operation, but they help you answer if the FCC asks about your station's activity. Licenses renew without proof of operation.

Tip: Log helps answer the FCC.

G2D09

Which of the following is required when participating in a contest on HF frequencies?

  1. A. Submit a log to the contest sponsor
  2. B. Send a QSL card to the stations worked, or QSL via Logbook of The World
  3. C. Identify your station according to normal FCC regulations
  4. D. All these choices are correct
Show the answer and explanation

Answer: C. Identify your station according to normal FCC regulations

During a contest, you must still identify your station according to normal FCC rules. Submitting logs and sending QSL cards are optional.

Tip: Contests: still ID per FCC rules.

G2D10

What is QRP operation?

  1. A. Remote piloted model control
  2. B. Low-power transmit operation
  3. C. Transmission using Quick Response Protocol
  4. D. Traffic relay procedure net operation
Show the answer and explanation

Answer: B. Low-power transmit operation

QRP means low-power transmitting, usually 5 watts or less for CW. QRO means high power.

Tip: QRP = low power.

G2D11

Why are signal reports typically exchanged at the beginning of an HF contact?

  1. A. To allow each station to operate according to conditions
  2. B. To be sure the contact will count for award programs
  3. C. To follow standard radiogram structure
  4. D. To allow each station to calibrate their frequency display
Show the answer and explanation

Answer: A. To allow each station to operate according to conditions

Signal reports let each station adjust to conditions, such as slowing down or repeating information if the signal is weak.

Tip: Signal reports help adapt to conditions.

G2E

Digital mode operating procedures

G2E01

Which mode is normally used when sending RTTY signals via AFSK with an SSB transmitter?

  1. A. USB
  2. B. DSB
  3. C. CW
  4. D. LSB
Show the answer and explanation

Answer: D. LSB

RTTY using AFSK through an SSB transmitter normally uses LSB by convention. Most other digital modes, like FT8, use USB.

Tip: RTTY via AFSK: LSB.

G2E02

What is VARA?

  1. A. A low signal-to-noise digital mode used for EME (moonbounce)
  2. B. A digital protocol used with Winlink
  3. C. A radio direction finding system used on VHF and UHF
  4. D. A DX spotting system using a network of software defined radios
Show the answer and explanation

Answer: B. A digital protocol used with Winlink

VARA is a digital protocol (modem) used with Winlink to send email over radio. It works on HF and VHF.

Tip: VARA carries Winlink email.

G2E03

What symptoms may result from other signals interfering with a PACTOR or VARA transmission?

  1. A. Frequent retries or timeouts
  2. B. Long pauses in message transmission
  3. C. Failure to establish a connection between stations
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Interference to PACTOR or VARA causes errors, which lead to retries, timeouts, long pauses or failure to connect. All the listed symptoms can happen.

Tip: Interference = retries, pauses, failed links.

G2E04

Which of the following is good practice when choosing a transmitting frequency to answer a station calling CQ using FT8?

  1. A. Always call on the station's frequency
  2. B. Call on any frequency in the waterfall except the station's frequency
  3. C. Find a clear frequency during the same time slot as the calling station
  4. D. Find a clear frequency during the alternate time slot to the calling station
Show the answer and explanation

Answer: D. Find a clear frequency during the alternate time slot to the calling station

FT8 stations alternate 15-second time slots, so answer in the opposite slot from the CQing station, on a clear frequency. Calling on their own frequency can collide with others.

Tip: FT8: answer in the other time slot.

G2E05

What is the standard sideband for JT65, JT9, FT4, or FT8 digital signal when using AFSK?

  1. A. LSB
  2. B. USB
  3. C. DSB
  4. D. SSB
Show the answer and explanation

Answer: B. USB

JT65, JT9, FT4 and FT8 use upper sideband on all bands by convention. This is true even below 10 MHz.

Tip: WSJT modes: always USB.

G2E06

What is the most common frequency shift for RTTY emissions in the amateur HF bands?

  1. A. 85 Hz
  2. B. 170 Hz
  3. C. 425 Hz
  4. D. 850 Hz
Show the answer and explanation

Answer: B. 170 Hz

The most common amateur HF RTTY shift is 170 Hz between mark and space tones. 850 Hz was used in the past.

Tip: RTTY shift: 170 Hz.

G2E07

Which of the following is required when using FT8?

  1. A. A special hardware modem
  2. B. Computer time accurate to within approximately 1 second
  3. C. Receiver attenuator set to -12 dB
  4. D. A vertically polarized antenna
Show the answer and explanation

Answer: B. Computer time accurate to within approximately 1 second

FT8 transmits and receives in timed 15-second cycles, so your computer clock must be accurate to within about 1 second. No special modem hardware is needed.

Tip: FT8 needs an accurate clock.

G2E08

In what segment of the 20-meter band are most digital mode operations commonly found?

  1. A. At the bottom of the slow-scan TV segment, near 14.230 MHz
  2. B. At the top of the SSB phone segment, near 14.325 MHz
  3. C. In the middle of the CW segment, near 14.100 MHz
  4. D. Between 14.070 MHz and 14.100 MHz
Show the answer and explanation

Answer: D. Between 14.070 MHz and 14.100 MHz

On 20 meters, most digital modes are found between 14.070 and 14.100 MHz. FT8 sits near 14.074 MHz, inside this range.

Tip: 20m digital: 14.070 to 14.100.

G2E09

How do you join a contact between two stations using the PACTOR protocol?

  1. A. Send broadcast packets containing your call sign while in MONITOR mode
  2. B. Transmit a steady carrier until the PACTOR protocol times out and disconnects
  3. C. Joining an existing contact is not possible, PACTOR connections are limited to two stations
  4. D. Send a NAK code
Show the answer and explanation

Answer: C. Joining an existing contact is not possible, PACTOR connections are limited to two stations

PACTOR is a link between exactly two stations. You cannot join an existing PACTOR contact.

Tip: PACTOR is a two-station link only.

G2E10

Which of the following is a way to establish contact with a digital messaging system gateway station?

  1. A. Send an email to the system control operator
  2. B. Send QRL in Morse code
  3. C. Respond when the station broadcasts its SSID
  4. D. Transmit a connect message on the station's published frequency
Show the answer and explanation

Answer: D. Transmit a connect message on the station's published frequency

To reach a digital messaging gateway, transmit a connect message on the gateway's published frequency. The gateway then answers and links you to the system.

Tip: Connect on the gateway's published frequency.

G2E11

What is the primary purpose of an Amateur Radio Emergency Data Network (AREDN) mesh network?

  1. A. To provide FM repeater coverage in remote areas
  2. B. To provide real time propagation data by monitoring amateur radio transmissions worldwide
  3. C. To provide high-speed data services during an emergency or community event
  4. D. To provide DX spotting reports to aid contesters and DXers
Show the answer and explanation

Answer: C. To provide high-speed data services during an emergency or community event

AREDN builds high-speed mesh data networks on amateur microwave bands for emergencies and community events. It is like amateur-run Wi-Fi networking.

Tip: AREDN = emergency high-speed data mesh.

G2E12

Which of the following describes Winlink?

  1. A. An amateur radio wireless network to send and receive email on the internet
  2. B. A form of Packet Radio
  3. C. A wireless network capable of both VHF and HF band operation
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

Winlink is an amateur radio email network that links to the internet. It can use packet radio and works on both VHF and HF, so all choices are correct.

Tip: Winlink: radio email, all of the above.

G2E13

What is another name for a Winlink Remote Message Server?

  1. A. Terminal Node Controller
  2. B. Gateway
  3. C. RJ-45
  4. D. Printer/Server
Show the answer and explanation

Answer: B. Gateway

A Winlink Remote Message Server is also called a gateway. It links radio users to the Winlink internet email system.

Tip: Winlink RMS = gateway.

G2E14

What could be wrong if you cannot decode an RTTY or other FSK signal even though it is apparently tuned in properly?

  1. A. The mark and space frequencies may be reversed
  2. B. You may have selected the wrong baud rate
  3. C. You may be listening on the wrong sideband
  4. D. All these choices are correct
Show the answer and explanation

Answer: D. All these choices are correct

An FSK signal that will not decode may have mark and space reversed, the wrong baud rate, or be on the wrong sideband. Any of these causes failure, so all choices are correct.

Tip: No decode? Check shift, baud and sideband.

G2E15

Which of the following is a common location for FT8?

  1. A. Anywhere in the voice portion of the band
  2. B. Anywhere in the CW portion of the band
  3. C. Approximately 14.074 MHz to 14.077 MHz
  4. D. Approximately 14.110 MHz to 14.113 MHz
Show the answer and explanation

Answer: C. Approximately 14.074 MHz to 14.077 MHz

On 20 meters, FT8 is commonly found at about 14.074 to 14.077 MHz. Its standard dial frequency is 14.074 MHz USB.

Tip: FT8 on 20m: 14.074.

Practice G2 with scoring Take a 35-question practice exam